Jump to content
SAU Community

Recommended Posts

I've been having this issue recently where my battery would go flat after turning the car off after driving for short periods like 15 minutes or so. The car doesn't even click over and you could see the clock on the cluster fading in and out. After jumping the car everything else is fine. Could it be a sub or an amp causing the battery to drain?any help would be appreciated.

Link to comment
https://www.sau.com.au/forums/topic/444007-battery-dies-after-driving/
Share on other sites

Yes.

It could be anything

Including your battery might be too old.

Your alternator might not be charging correctly.

I've taken the sub out , I'll see how it goes . I'll even put some distiller water in the battery as well

I'd say the altenator must be working or the thing wouldnt have any power to drive (seen as its completely dead after key off)

I'd look at battery first but you can also check altenator as well

If you dont already have one, go buy a cheap multimeter from Jaycar or Supercheap etc. Get the car running and check the Voltage with the car running. Check either by putting the meter probes on each of the battery terminals, or you can also put one on the positive out of the altenator and the other on a good ground in the engine bay. Between 14.0V and 14.5V means the altenator is working properly.

Get a second person and keep the meter somewhere as above, checking voltage when the car is turned off. The BEST a battery can get when off is 12.6V, but usually anything around 12V is fine. If you have less than this, and judging by your description you may have alot less, you have a problem on the battery or cables. Check that the cables/terminals are clean and have a good earth and good connection on the positive end as well. If that all looks good then I'd say its battery.

Another way to check the altenator as well is to check the R terminal. Best done with a test light, putting it to positive on one end and probing the R terminal should make the test light light up while the car is off. when the car is running, putting the clamp on ground and probing the R terminal should make the test light light up

Should be plenty of info to help you out, and multimeters arent expensive, and can be very handy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...