Jump to content
SAU Community

Recommended Posts

R33 gtr rb26 engine, head has been serviced new headgasket, arp studs, new valve stem seals, n1 oil pump, tomei oil restrictor, near new water pump and many more things.
Comes with r33 gtr turbos etc
Intake manifold + throttle bodies

Comp tested 160 1,2,3,4 157 5,6

-4000

Garrett 2860r -7 turbos great condition fully rebuilt 2500kms ago -1300

R32/33 nistune ecu, has tune just for exhaust intake and boost increase -450

R32 gtr seats pretty good condition -550
R32 gtr diff -500
R32 gtr rear wing -100
R32 front and rear strut braces -150
R32 gtr tailshaft -100
R32 gtr exhaust 3.5 to 5 inch tip

r32/33 gtr after market downpipe -100

r32 apexi duel bovs -100

r32 gtr intercooler and piping -200

Rb26 r33 gtr gearbox, no noises or crunches perfect working order -900
Rb26 camtech cams used for start up only! Unknown spec but good for power, can drop in with stock valve springs -300
Rb26 apexi air intake + filters -100

Will upload pics on request

message me or text me on 0481360765 for more info

Edited by nickgtr32
Link to comment
https://www.sau.com.au/forums/topic/445502-rb26-engine-and-r32-gtrrb26-parts/
Share on other sites

Rear sway bar sold

Also have full r32 gtr brake set up for sale

4 piston fronts

2 piston rear

New seals

New discs and new genuine brembo race pads. Sprayed in black.

-$650

post-134644-1405944664586_thumb.jpg

N1 oil pump suit rb26 -$150

post-134644-14059445991667_thumb.jpgpost-134644-14059446092293_thumb.jpg

R32 gtr fibreglass headlight intake -$50

post-134644-14059445679537_thumb.jpg

R32/r33 gtr engine mounts near new -$75

post-134644-14059445497729_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...