Jump to content
SAU Community

(Nsw) Wsid Meet - Night Of Drags 23/7/14

Brick

By Brick,
in Wagoneers

 Share

Recommended Posts

Brick Mentor

Brick

Posted
Posted (edited)

Who's keen for a night of drags at eastern creek?

Meet 530pm at scrutineering.

Cost is $50 to race or $20 to spectate.

Edited by Brick
Link to comment
Share on other sites
Brick Mentor

Brick

Posted
  • Author
Posted

I have everything ready to go, just trying to make it happen with needing the car off the road a few days is a challenge right now. Should have that sorted soon, but it wont be before this race night. This is more of a before tune test night

Link to comment
Share on other sites
PN-Mad Grand Master

PN-Mad

Posted
Posted

Nice work Josh.

Just a bit of a correction, they bumped up the cost to $55 bucks for competitors.

Just go to WSID website for all the info, and a guide if you've never done it before. You need a suitable helmet, ankle to wrist clothing. No special licence is needed.

And the most important thing, just have a go. I've seen everything go down, from a 90cc farm bike, hiluxs, to 8 second GTRs and faster things too. Just get out and have a go!

The cost is minimal to what you'd get done for on the road if you got booked at 160!

  • Like 2
Link to comment
Share on other sites
PN-Mad Grand Master

PN-Mad

Posted
Posted

Hahaha, yeah it will, but not when I've got a trackday booked in the future.

If the motor or tranny pops, I want the time to sort it out. Unfortunately I'm OS for this.

  • Like 1
Link to comment
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • klutched
      GOT SUM's RB34

      By klutched · Posted

      This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • Dose Pipe Sutututu
      Rear suspension upgrades

      By Dose Pipe Sutututu · Posted

      A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
    • sonicii
      Newbies

      By sonicii · Posted

      215/45/18 tyres are probably a little on the low side compared to the factory tyre, it should be closer to a 245/45/19, which will get you about an extra 11mm of height, and should make you speedo read a bit closer to reality. 245/45/19s will be a bit too far the other way and you risk a speeding ticket as your speedo might read slower than your actual speed.  245/40/19s would be correct if you are going to 19in rims, they will give you a similar total diameter to the 245/45/18 tyres.  
    • GTSBoy
      Rear suspension upgrades

      By GTSBoy · Posted

      That's something I forgot to put in my list. The aggressive anti-squat in R32 is a f**king menace. I still need to decide if I'm going to drag the subframe out of my car and weld in the GKTech corrector kit. The main reason to dither is the need to switch to spherical joints in the lower arm to account for the twist induced in the rear pivot caused by lowering the front pivot. And yes...we do put better subframes in R32s, and I wish I'd gotten an S14 one instead of an A31 when I did the "take off and nuke it from orbit" HICAS delete all those years ago.
×
×
  • Create New...