Jump to content
SAU Community

Recommended Posts

  • 6 months later...

Hi,

For anyone still interested in this, I had the same issue for the past four years on my 1994 R32 GT-R. The HICAS light would come on a few minutes after driving and the steering would go dead heavy.

I had Nissan and another workshop run the HICAS diagnostics multiple times - no problems: the back wheels did their flappy thing and everything.

Finally, just this week Custom Importz in Lonsdale SA found and fixed the problem. There were actually three faults:

1. The speed sensor in the back of the instrument cluster was faulty.

2. The steering angle sensor was faulty

3. (Not such an issue). One of the rear solenoids was faulty (this did show in up diagnostics but replacing it not fix the issue until the above two were fixed).

For anyone having this problem, follow the advice above to run the HICAS diagnostics, check fluid levels etc, but also get your shop to check these sensors in around the console and steering column. They were the "missing link" that did not show up in diagnostics.

Glenn

No, the HICAS solenoids are the big arse lumps just in front of the driver's side axle.  Hydraulic pipes coming down the chassis rail to them from the front, flexibles going out of them to the HICAS rack.  This image of an S13 shows it, correctly named, as the "fail-safe valve".

hicas1.jpg

 

And following up on Glenn's update......looks like Missileman was on the money with the speedo.

It will come to the point where we will need to look at wiring diagrams for non-HICAS Nissans of the era to work out how they ran their power steering assistance control without a HICAS computer, so we can delete the troublesome buggers of things when even the usual bypasses we do stop being good enough.

I'm trying to figure out why my steering is heavy at low speed.

So far I have figured out the speed out of my cluster is fluctuating around 10kmph or so (looking at the software on my link ecu) Also measuring the yellow/green wire at the Hicas ecu the volts are fluctuating at a constant speed.

Could this fluctuating be causing the hicas to stop adjusting the valve in the steering rack?

Glen did you have to replace the whole cluster or can the speed sender be replaced on it's own?

I tried many times to get the car to enter diagnostic mode but it wouldn't do it..

Cheers!

 

The speed signal from the speedo head to the ECU and to the HICAS CU is a square wave 0-[something, I think 5] volt PWM signal.  You will see it vary under normal circumstances.  But I suppose the speedo head could fail in a way that the indicated speed is fixed, or never goes low enough to boost the assistance.

Look at the R32 GTR workshop manual pdf for guidance on how the AC speedo sensor signal is converted to the square wave signal and what you should see at various road speeds.  Then use a scan tool to interrogate the HICAS CU for what it's seeing.

Thanks for the reply.

There is probably nothing wrong with my speed sensor (I just assumed that the reading fluctuating so much indicated a problem) and my Hicas issue is most likely something else. 

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...