Jump to content
SAU Community

Power Loss On Downshifts, Bouncing Idle And Slight Hesitation At Specific Rev Point -R34Gtt


Recommended Posts

Sorry my bad. I assumed that going a 3L you would upgrade the supporting mods, water and oil pump, timing belt, clutch and at least a dyno tune. Obviously not the case, I apologise.

You can't do it without a timing belt. Water pumps are cheap as. The rb30 oil pump is fine. Shim the relief valve for free.

And I tuned it on the dyno.

Widebands are the best.

I also thought my car was running rich.

Bought wideband.

Observed AFR.

Changed fuel maps to suit.

Car running correctly.

See also:

Got tune. Cold start was terrible. Idle was terrible (17:1).

Made 30 seconds of changes.

Car running correctly.

See also:

Car tuned on E85. Corrections for 98 not entirely right (known).

Get E58 or something in tank after tank swap.

Made 15 seconds of changes in correction map.

Car running correctly.

See also:

Changed injectors from 1000cc to 1400cc.

Car not running correctly.

Made 2 minutes of changes to fuel map.

Car running correctly.

GET A WIDEBAND

  • Like 2

Doing a RB25/30 conversion for less then $3k can be done IF you can do all of the work yourself and all good and well these guys say you can cause i did it is not a fair statement, you couldn't take you car to someone ( and not a mate ) and get it done for that, no way in hell

It also come to what supporting mods you do and to what level and how properly you do the conversion as we all know there are cheap way to do some stuff which isn't exactly the best way of doing it

So the real question would be can Ron do it for less then $3k done and dusted ?

  • Like 2

Again with the wide band, if tuned properly you shouldn't need one, nice to have but not needed cause really you can only do so much on the street before it should be put on a dyno and tuned properly

^^ This really clever fellow here knows me more than I know myself !!

Yes.

It's based on many things you have posted.

For example.

You specified how exactly you were going to block up your bov return. And did it weirdly anyway.

Someone who knows what they are doing just does stuff.

I do really hope you can get the car sorted out.

22 pages on AFM vs. BOV lol

I reckon, sell Power FC, BOV, AFM - buy Adaptronics, block up BOV port/return dose & bake tyres all day

  • Like 1

So in in Rons case it would go

Nistune, sell

Power fc sell

Adaptronic

???

Profit?

Edited by Ben C34

flutters is the shit man... you won't look back.. and no more reversion, no more stalling crap, no more dirty AFM, etc.

rip skids & be happy

  • Like 1

Again with the wide band, if tuned properly you shouldn't need one, nice to have but not needed cause really you can only do so much on the street before it should be put on a dyno and tuned properly

True enough for anything over 100kmh with a power run. The 97% of the driving you use a street car for however can be done with a wideband and some tinkering. The power runs is what the dyno is for but that is really only a small fraction of the time (money!) it takes for a tuner to tune the car, but I agree - it's no dyno replacement.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
×
×
  • Create New...