Jump to content
SAU Community

No Spark To Coils/plugs. Help Pls! Rb20Det

Anthony9five

By Anthony9five,
in General Maintenance

 Share

Recommended Posts

Anthony9five Apprentice

Anthony9five

Posted
Posted

I replaced the rocker cover gaskets and spark plugs on my rb20det. It was working fine.

Put it back together and wouldn't start.

I pulled a coil and plug out and attempted to start it and found there was no spark.

What could cause this?

Sinista32 Grand Master

Sinista32

Posted
Posted (edited)

You need an earth on the ignitor I don't see one in the picture above

I do see the wire to the left near the grey plug tho

Then bolt it to the block in the factory position

Edited by Sinista32
  • Like 1
Anthony9five Apprentice

Anthony9five

Posted
  • Author
Posted

Solved or still an issue

Unfortunately it's still an issue. I ended up doing a test at all the coil loom outputs and I'm getting power. This makes me think the problem are the coil packs but it seems odd because they were working fine before.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...