Jump to content
SAU Community

350Gt Climate Control Problem/front Seat Removal.

chiefster1976
 Share

Recommended Posts

chiefster1976 Apprentice

chiefster1976

Posted
Posted

Hi all.. I have a skyline 350GT 04.

Im having issues with the climate control... On 18 degrees the AC works fine for cold.

The problem is even on 18.5degrees the temperature is like having it on full heat setting, doesn't seem to be

holding correct temp...

Is this some kind of resistor or part replacement?

Im also looking at getting the notorious ripped drivers seat fixed on the leather/ vinyl seat.

I was wondering if it is possible to remove the seat BASE only with removing the whole seat? ;)

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

When someone has pulled apart the panel near the drivers knee, when they have refitted it they have not properly (or at all) connected the pipe that senses cabin ambient temperature. If you pull off this panel, in the left hand side under the mirror fold-on button you will see a little pipe that is supposed to be connected to the panel on the left hand side where there are some little cuts in the panel for the pipe to 'breathe'. I bet that is your problem.

sonicii Veteran

sonicii

Posted
Posted

Im also looking at getting the notorious ripped drivers seat fixed on the leather/ vinyl seat.

I was wondering if it is possible to remove the seat BASE only with removing the whole seat? ;)

If it is anything like the sedan seats. you need to remove the whole seat so you can dismantle it.

chiefster1976 Apprentice

chiefster1976

Posted
  • Author
Posted

Thanks for replies... Seat base was relatively easy to remove. Removed full seat then seat base... :woot:

As for the Climate control issue I checked the pipe on the back of the panel as discussed and the pipe was STILL attached. I tried to get my hand as far as I could and followed the pipe.. It goes into a small grey box near the back of the stereo and has a hole on the top of the little unit... It looks as though it should have a pipe on top of the grey box. I had a good feel around as far as I could go and there doesn't seem to be a pipe! :angry:

could there be an electrical or part issue?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Of course, the sensor or wiring could be stuffed, but usually that sort of thing throws a code.

If you were local I could plug the consult into it and check the in cabin temp is correct, that would at least tell you the sensor is fine or not.

  • Like 1
sonicii Veteran

sonicii

Posted
Posted

The sensor is separate to the hose. It is in the hose fitting on the 'kick panel' end and should have a cable connected to it. The hose is just there to draw air over the sensor.

  • 2 weeks later...
chiefster1976 Apprentice

chiefster1976

Posted
  • Author
Posted

Thanks for replies!!

So im guessing I have to get it on a fault code machine or probably cheaper just buying the sensor?

After taking my seat out the AIrbag light keeps flashing on now!! Arhh!!!!! :verymad:Everything plugged back in OK under the seat!

Is there a way to reset ECU without a trip to Nissan? Take off Battery Earth for a few minutes work?

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

If you had your battery connected when you undid or re-did your airbag plug, it causes it to throw a code - I have actually read reports of the airbag going OFF when it is plugged back in with the battery connected. You might have dodged a bullet. Some codes can go away by unplugging the battery and leaving your headlights on for 5 mins to completely flatten the battery. Give it a go.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

The airbag circuit can go off even with the battery disconnected, as there is a residual device that powers them even if the battery is damaged. Not something you want to muck around with.

I can clear codes on the Consult 3 like I said, but where are you located Gavin? Makes it hard to know if I can help. Otherwise go to nissan, and be ready to bend over. :P

sonicii Veteran

sonicii

Posted
Posted

I am fairly sure the airbag light will clear after a certain number of 'ign on/off' cycles with no errors detected.

I used this process which worked after fixing the wiring in the seat, before I had my Blazt cable.

http://g35driver.com/forums/repairing-detailing-diy/163319-diy-airbag-reset-instructions-03-07-g35-coupe.html

  • 2 weeks later...
chiefster1976 Apprentice

chiefster1976

Posted
  • Author
Posted

Hey all... Does anyone know where I can order a new sensor for the climate control at the drivers left knee area?

Any Part number at all?

Im thinking its probably just best to replace the sensor and hopefully this will fix the climate control heat settings problem???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...