Jump to content
SAU Community

Recommended Posts

Hi all,

I have been trying to get some information clarified. In NSW, legally how is a car dealer meant to advertise a Demo car that has been registered. Is the advertised year determined by Build date or Compliance date?

For example, a car has build date of 2013, compliance date of 2014 and is a MY14. It is a demo car that has had registration for three months. What year are they legally meant to advertise it as? Again it's a Demo, so I guess that would qualify it as a used car? If so I'm sure that should change things?

I know it's a bit of a grey area especially when it comes to a brand new car, It is also different in each state.

In S.A it doesn't matter if it's a brand spanking new car, a demo or a fully used car, it has to be advertised by the build date.

Again just after information for N.S.W. I would Appreciate any help.

Cheers,

Paul

At a Volvo Dealership Paul, this 3l turbo straight six...

Terry-3_zps4e1b5e7e.jpg

had been driven by a director over the past year for 11,000Km.

Build Date = 2011

Model = 2012

Complied = 2013

Bought as a 1st Owner = 2014

Upon transfer of registration (with new car 4 yr manufacturer's wty), it reads as a 2013 car.

Personally, we though it'd be 2012.

Anyway-y-y-y-y...

It's goes off tbe compliance date

yup, compliance date.

warranty goes by first date of registration.

Ok... They sure have it both ways then. I bet when it comes to resale it will be based on Build date :(

Like I said in S.A , no matter what, the car has to be sold by the build date. I must say its a bit disappointing, from what I have found out it is a bit of a grey area. I also would have thought the rule/law would change when it has been registered? I would expect that from a dubious used car sales place etc. but not from a premium dealer especially when forking out a bit of coin. Would be nice if they said it's really a 2013, another lesson learnt I guess, don't trust anyone :(

I also thought it would change things when it's been registered all ready,

When reselling, you would also advertise by the compliance date.

The reason we go off compliance, is due to some manufacturers taking literally 1-2 years to get compliance after the car had been built.

Who would want to buy a 2yr old new car?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...