Jump to content
SAU Community

Cam Chain Sprockets Vq25Det M35 Axis

Philmeup_s13
 Share

Recommended Posts

Philmeup_s13 Newbie

Philmeup_s13

Posted
Posted

OK, pretty much this has turned into quite a saga with me.

A little while ago I got a local workshop to change the timing chain as it was start rattle/ play up, a month or 2 after that my car started to miss, not rev and after a few days actually started to stall completely (not great while doing 70kmh in traffic).

I took it back to the same work shop and was informed that it was the cam chain sprockets that had given up and were putting the timing out. This was February this year, I've been given the run around ever since, parts ordered/not ordered/they're coming only 2 weeks away/usual workshop bulls**t.

The owner told me that he was getting them through a Japanese supplier as Nissan Australia was hellishly expensive, mind you still coming in at $1200 for the parts. I have spoken to Nissan and they informed me if i buy new through them that they will be $1300 EACH and I need both - for this price I could buy a whole second hand engine...

Before I bite the bullet and do this i'm wondering if anyone would either know of someone who can source these parts new for me, or that has an engine I could grab some second hand off.

On another note, this is the worst experience i've ever had with a Japanese workshop (and ive come across some pretty average ones), they've had my car 6 months and still no parts, i've had to buy another car to drive in the meantime and its gone past the point of doing my head in...its a joke

Any help or suggestions is greatly appreciated.

Commsman Veteran

Commsman

Posted
Posted

What a saga. Somethings smells bad with this. You're right, for that money you could buy a wreck & strip for parts.

If you know the part number/s, do a price check at http://www.amayama.com/. That will at least give you a starting point to determine if you are being touched up.

Good luck with getting this sorted out. You must be a patient guy to be getting the runaround for 6 months.

Philmeup_s13 Newbie

Philmeup_s13

Posted
  • Author
Posted

Thanks guys, Its definitely the sprockets as you can hear them clacking/clunking when you come off load, and they slowly got worse over a period of a couple of weeks.

Much appreciated Scotty, I've actually bought an AFM off you in the past (i'm local to you), I will shoot you a PM later today.

Comsman - Everyone's got a threshold, I actually had to get my old man to talk to him the last couple of times as once when I rang he refused to talk to me and hid behind his secretary who subsequently copped a blasting, was about to go round and starting throwing things at him until my old man talked some sense into me.

walkoau Mentor

walkoau

Posted
Posted

bummer you didn't post this up a couple of weeks ago.... i just sold a complete brand new set on ebay for only $530 this was for both sides sprockets magnets sensors and covers.

a lucky guy in NZ got himself a bargain.

when i first brought my m35 it had a problem and under warranty it was misdiagnosed as these. long story short i drove the car running like a pig for a few weeks, until the parts came in from japan. in the mean time i found a loose coil lead. fixed the problem. took the car back to the mechanic when the parts came in. he said i could keep the parts as they are a common fault and i would prob need them eventually. "Just don't tell the dealer" he said.

Daleo Grand Master

Daleo

Posted
Posted

I still don't understand where this "common fault" crap came from, I have never seen worn cam chains/sprockets, only broken components.

Perhaps if you were a bit more experienced with these engines; you might know what's going on. :domokun:

So many experts with these now...

  • Like 3
walkoau Mentor

walkoau

Posted
Posted

I still don't understand where this "common fault" crap came from, I have never seen worn cam chains/sprockets, only broken components.

He said my prob was the sensors/magnets, not the sprockets.... Keeping in mind he didn't really have a clue anyway as it was misdiagnosed.

It was low on power. He simply thought it was not automatically advancing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...