Jump to content
SAU Community

Recommended Posts

Recently I have noticed a increase in the volume of the popping and sometimes cracking noise from my exhaust when I'm de accelerating. What could cause this? The engine is stock with stock intake it has the usual 3.5 inch exhaust with cannon and a high flow cat. I haven't changed anything on the car but have been told that my oil rings could be stuffed. Would the popping noise increase due to worn rings? Also if your turbo is on it's way out, would this increase the pops?

It used to do it when it was over due for a service then when it got serviced it would go away. Anyone have any ideas? I'm stumped.

Link to comment
https://www.sau.com.au/forums/topic/448243-r33-popping-cracking-exhaust-noise/
Share on other sites

Yeh funny you mention it becuase my r33 gtr is completly stock down to the exhaust system and occasionally i get a little poping when de-accelerating, never really crackling but.

how does your car perform with the 3.5 inch exhaust sytem on stock internals? only becuase im about to get a system made up but i was gonna go 3 inch? how loud is your system?

From inside the car it's not that loud. I run the stock manifold with 4 inch dump and 3.5 system, highflow cat and a drager cannon. I have been told that when you get on it it is a tad rumbly from outside :yes::wub::woot:

I was going to put a different cat on it to make it even louder but then you would get that droning noise through the car :down:

Car runs fine. Only draw back is you can't have the car to low because of the zorst. I've been told that it sits higher than most 33's.

Its got to do with your exhaust, now that its opened up and is more free-flowing you should notice a slight increase in boost as the turbo is able to flow more freely, and thats why it pops, because now its "out of tune" but the slightest amount. nothings really going to fix it until you get a tune, i.e. nistune or something.

but as to why it actually pops I just assumed is was unburnt fuel, but I'm no expert, just sharing my knowledge.

sounds legit, becuase i rang castle hill exhaust and the quoted me $950 for a 3'' Mandrel bent (Mild steel/stainless cannon) with 100cell

hi flow cat. you think this would be suitable for my setup or should i go 3.5 for when i do more work? i just dont want the drone like you mentioned and i dont want to loose back pressure :no:

Its got to do with your exhaust, now that its opened up and is more free-flowing you should notice a slight increase in boost as the turbo is able to flow more freely, and thats why it pops, because now its "out of tune" but the slightest amount. nothings really going to fix it until you get a tune, i.e. nistune or something.

but as to why it actually pops I just assumed is was unburnt fuel, but I'm no expert, just sharing my knowledge.

The exhaust was on the car since I bought it :) and it never used to have this popping issue that bad.

sounds legit, becuase i rang castle hill exhaust and the quoted me $950 for a 3'' Mandrel bent (Mild steel/stainless cannon) with 100cell

hi flow cat. you think this would be suitable for my setup or should i go 3.5 for when i do more work? i just dont want the drone like you mentioned and i dont want to loose back pressure :no:

I'd probably go the 3 inch and then get a decent resonator. That should give you the drone your after.

"i dont want to loose back pressure" and "That should give you the drone your after"

Wait, what?

Anyways, its just unburnt fuel. You could double check using a consult cable. Maybe the "closed throttle" signal isn't working properly when you let off the throttle.

You most certainly want to lose back pressure, you have a turbo car + you shouldn't be worrying about scavenging effects. Get a 3.5" exhaust with good mufflers (e.g. Magnaflow), you won't have drone issues then. I run a 5Zigen 3.5" cat back (two mufflers), no drone at all and car went harder. Shame the mid muffler cracked and had to replace it with an inferior muffling Xforce one.

Popping and crackling is unburnt fuel in a hot exhaust. When is the last time you changed the spark plugs?

  • Like 1

If it is the closed throttle signal, how would you check that?

The easiest way I can think of is with a consult cable. You can see the signal in realtime or you can create a log over a period of time, ie going for a drive. I think theyre a must for any skyline etc owner who needs to track down a fault.

I'm going to lock in broken exhaust stud/s.

Documented RB25 issue over time. The release in torque on the manifold could have introduced air into the exhaust on over-run, causing the unburnt fuel to ignite with the extra presence of oxygen.

;)

Huh? :huh::mellow:

Do they snap off over time? Is that what you are saying? Or are you saying that they snap when you change the manifold? If this is happening wouldn't I hear a exhaust leak on the manifold itself?

Yes the studs weaken and snap after many years, especially if yours have not been replaced from the factory.

However mine are new and my car still makes little pops and burbles on the overrun. Was particularly noticeable after fitting a new 3 inch exhaust. If you don't notice any issues with fuel consumption I wouldn't be too concerned.

I'm going to lock in broken exhaust stud/s.

Documented RB25 issue over time. The release in torque on the manifold could have introduced air into the exhaust on over-run, causing the unburnt fuel to ignite with the extra presence of oxygen.

;)

Now that you mention it, my Skyline used to pop on decel even with a standard exhaust. Since replacing the manifold with one without a crack it doesn't pop any more!

I don't doubt that 3inch exhausts pops and carry on at all, but none of that explains why the popping has actually increased over time with no other mods.

You might not hear the exhaust leak on throttle over the exhaust, or it may be a very small leak.

It's just my theory, take it or leave it ;)

Nothing to be all that worried about anyway.

I guess it could be any gasket on the exhaust side too, by this logic.

Now that you mention it, my Skyline used to pop on decel even with a standard exhaust. Since replacing the manifold with one without a crack it doesn't pop any more!

Now that you've mentioned it, my rear turbo gasket started leaking. I had some good pops.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...