Jump to content
SAU Community

Changed Turbo Water Feed Now No Heater

DarkClowns

By DarkClowns,
in General Maintenance

 Share

Recommended Posts

DarkClowns Apprentice

DarkClowns

Posted
Posted

Changed turbo water feed line as hose was weeping from intake to y pipe to turbo on rb20det in r32 topped up coolant again and now heater isnt working.... bleed it 3 times and at best its slighty warmish then goes cold again..... wtf.... help

Ben C34 Grand Master

Ben C34

Posted
Posted (edited)

Can't help you.

Changing the line doesn't do anything to the heater. So either your heater is blocked now for some reason or you aren't bleeding it right or you did something else.

Edited by Ben C34
DarkClowns Apprentice

DarkClowns

Posted
  • Author
Posted

Ok so i found that when i set it to FH it blows hot air.... theres a metel sensor or something in top heater hose has elec plug and metel t peice with rubber block off on it ...can this be causing it as pulled the hoses/sensor out way to get to turbo water feed ???

jiffo Mentor

jiffo

Posted
Posted

As far as I know, these cars run coolant through the heater core constantly, cabin heat being regulated by the air mix door.

That sensor in the hose at the firewall tells the aircon amplifier unit the actual coolant temp.

If you've disconnected it you'd see a fault code 23.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
×
×
  • Create New...