Jump to content
SAU Community

New Sau:nsw Members - Please Post In Here.


Recommended Posts

If you have just sent in your membership forms please post in here, stating your name and the date the form was sent and payment was made.

This is to consolidate our data base for our executive committee, as to streamline new memberships, and allow our exec to answer any questions you may have.

(Please read this first (http://www.sau.com.au/forums/topic/365434-s-a-u-n-s-w-club-membership-faq/), and if your questions still aren't answered, then feel free to add a question.)

Also, please remember that the Executives who run Skylines Australia NSW are all volunteers doing this purely for the love of the club and the benefit of its Members, so your patience is greatly appreciated!

Regards

Andrew

Hi my name is Chris and i sent my application form and payment on the 18th August

Hi Chris, Thanks and welcome to the club.

Still have not received my sticker and member card =)

Joined End March..

Sorry for the delay, The club secretary just had a bebbeh and moved house, as far as I know member cards have been sorted now and I will check on the stickers for you.

  • 2 weeks later...

Hi

Name: Pak Tsun (Adix) Wong

Date the form was sent: 2nd of March

Date the payment was made: 2nd of March

I know I have the "NSW Club Member" banner thing on here, but I have not received any sticker or membership card so far...

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...