Jump to content
SAU Community

Recommended Posts

There never was a stock 300GT manual, so hard to say how well it will drive.

Given that.. I think that is a cheap price, make sure you get it in writing that this is a complete 'turn key' job and they will resolve any issues it creates. As it is unlikely anyone has done this before, so there is likely to be several 'unknowns' along the way.

My guess is that figure is for the mechanical work alone..

Thanks for the replies. Its my first auto car. My previous was a renaultsport clio which was very entertaining. Im finding the 300gt a little boring by comparison. After the responses and talking to a couple people I think I might just leave it as is until I can get something better. Lesson learned. Dont buy autos

Yeah you will need the interior trim too and some form of electronics to run it? Because the standard ecu is for an automatic.

FWIW in my R34 the auto ECU runs fine with the manual box, even the Nistune works fine. Your mileage may vary.

I know electrical will be annoying. What benefits is there of going manual. Is will still be a gutless 30dd

Cos manual = more fun?

Indeed manual does = more fun. Shame there is f all manual sedans around.

There are a few.. when I bought mine, there was 2 others on carsales. But at the moment, it seems the only 350GT sedan on there is a CVT.

Thanks for the replies. Its my first auto car. My previous was a renaultsport clio which was very entertaining. Im finding the 300gt a little boring by comparison. After the responses and talking to a couple people I think I might just leave it as is until I can get something better. Lesson learned. Dont buy autos

Don't say that... Whilst a manual 350GT (for example) may be more 'fun'... I enjoy my 5 speed sports auto far more... torque torque torque and very responsive... + the manual mode is good fun if you want to hold gears :)

Have you considered selling your 300GT and using the money that you would have outlayed (eg: $3000+) towards a 350GT Coupe?

Edited by Sikahalv

I would just hang out until a 4dr manual appears for sale. Too many unknown 'gotchas' with converting a 300GT to a manual, unless you know someone who has done it before. You could possibly need a whole aftermarket ECU to make it work properly..

  • 2 weeks later...

I decided to not go ahead with the conversion. As much as I would prefer a manual I may look into a v36 sedan with the better engine and hopefully better auto. If the 5 or 7 speed auto is greatly improved over the 300gt then I could forgo a manual I a suppose. Anyone gone from the old v35 auto to the newer? And are they that much more responsive?

I Drove a V36 sedan, 350 GT, 5 speed auto. I was keen to buy, but the dealer could not supply the de-reg papers from Japan. Despite having a 235kw engine I did notice any major performance increase over the V35 coupes. I think it may be on account of it being heavier, and apparently they have less torque.

It was a nice car, but there was a bit of lag from the paddleshifters when changing gears.

I settled on a V35 coupe (we have a 7 seater Dualis for my wife/kids anyway) and don't regret a thing. Without a doubt, the best car I have ever owned.

I think it may be on account of it being heavier, and apparently they have less torque.

I thought the VQ35HR had the same torque figure? It recovered the torque the DE revup engine lost and increased power further.

And it was 230kw in the V36.

Edited by sonicii

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...