Jump to content
SAU Community

Recommended Posts

I'm replacing the Weldon with a Fuelab which will give me some room to put the cool next to the surge tank which will have a thermo fan triggered by the ecu at a set temp and be protected by the rear diffuser

Off topic

ut where are you getting the fuelab from?

On the subject of the E85 getting warm, run a cooler under the car where the airflow can cool it and splice it into the return line (low pressure side).

Vehicles like M3's use that setup.

The only issue with a fuel cooler is mounting it in a suitably safe and protected way. Takes a bit more planning than an oil cooler etc.

Exactly !!!, that is why I haven't put one on yet, as my tuner said, I am better off burning an engine then you the whole car

But with what happened at the trackday I need to fit one, my idea is to mount it next to the fuel pump under the back and have the return line run through it then into surge tank and have the factory rear diffuser protect it from flying debris

  • Like 1

Its possible to put it into a grilled or fluted box surround to protect it.

Yep. But the consequence of it getting damaged could be huge.

I just wanted to make the point it's certainly not as simple as whacking on a fuel cooler.

What would be great is a heat exchanger setup, with coolant pumped through a cooler in the fuel tank, then through an external cooler. If it gets damaged only coolant pisses out, car doesn't burn..... but that's in my too hard basket.

I find them quite up to date.

This is united

http://www.unitedpetroleum.com.au/united/fuel/ethanol-85/e85-store-list

This is Caltex

http://www.caltex.com.au/HelpCentre/Pages/CaltexFinder.aspx

Select e-flex in the finder and zoom in.

I found 2 in the newcastle area that sell e-flex.

One is in Charlestown and the other is in Hamilton

There's one that's been selling E85 in Ipswich in QLD for over 3 months that still isn't on that list, so i'm sure that there may be others in other states that aren't on there but do sell it? Would be good to have one somewhere between Syd and melb for example.

For reference this is a map I made from the united list in June

The bottom tank is still quite warm though.

What you want is to run the aircon lines to the fuel tank, and have it automatically switch on as required. :P

Probably a dumb question but what is making it hot in the first place, the pump ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...