Jump to content
SAU Community

Recommended Posts

Hey guys been a while since ive posted but finally going to start looking for a gtr, been a bit out of it for a while, but want to know the dos and donts on buying a 32 gtr. If i recall, the early ones had oil starvation problems, and later ones they fixed it? Also I have a N1 oil pump off a 32 lying around, were these fitted to the later ones or only the N1's. Also feel free to throw in some other tips on the weaknesses and pros and cons of the early ones and later ones. Cheers.

Link to comment
https://www.sau.com.au/forums/topic/451304-tips-on-buying-a-32gtr/
Share on other sites

There's already heaps of info on this topic

Try some of these, use the search first if you need any more info.

General Skyline checks:

http://www.sau.com.au/forums/topic/35129-im-buying-a-skyline-what-should-i-look-for/

Little more R32 GTR specific:

http://www.sau.com.au/forums/topic/288375-bnr32-gtr-buying-guide/

32GTR Year differences:

http://www.sau.com.au/forums/topic/443799-r32-gtr-year-model-differencesimprovements/?p=7298091

Best piece of advice around here is; do not believe the listed KM's unless you have every km accounted for in a log book/records, even then...

Paint fade on plenum usually indicates 100k+ km's - but can be easily painted.
Run the VIN through Nissan FAST to make sure it all matches NISSAN records - dedicated threads for this. (paint/model etc).

Hope this helps.

  • Like 3

yeah im aware as looking underneith for rust around windows under wheel arches etc. Also I have a good understanding of general wear and tear and most of the time the kms arnt correct, more just after technical stuff about the early ones and the ones built after 93. I know the 93 > had fixed the oil pump, but does it run the N1 pump, same just refined. I know that they had oil drain back problems, but was it fixed in the later models? Mainly after the weaknesses and strong points of the 2 if it makes sense, obviously any car I look at im going to get up on the hoist and poke things to see the struture side of things. A few years ago I did look at a couple but for the money I was going to spend it wasnt worth it as I have never seen so much bog and bad welds on a car, so now Im prepared to spend a bit more so I am doing my homework again so I make the right decision.

ah k fair enough its what I thought just sometimes the odd chance I know some car manufactors on the last model they throw all the parts that were left over on the latest model. But in saying that a 93 onwards would be a better buy than a earlier one.

Not really.

Yeah sure, Nissan addressed the oil pump issue in the later models but it only tends to fail at highly modified applications.

If you are just using for street use, you'd be fine.

Generally buying a later model R32 GTR will just mean it's new then the older models and most probably have more life in it (Turbo's and Engine) before you need to rebuild anything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...