Jump to content
SAU Community

Recommended Posts

Hi All,

I've had a quick search but couldn't find a definite answer. I have an R33 S2 GTST and it's got a few mods to it:

FMIC

3" Exhaust to highflow Lukey exhaust

Nistune ECU

10 pound wastegate spring

Splitfire Coilpacks

To my knowledge it's running a stock set of injectors and fuel pump (yet to confirm) - I may have forgotten something, sorry.

It was last tuned with a stock SMIC and the exhaust as is. My question is would I get more power from the car if I got it retuned with the FMIC this time? It made just over 170 at the rear wheels but after reading a few threads on here (this for example - http://www.sau.com.au/forums/topic/10567-front-pipe-dump-pipe-beforeafter-dyno-results-203rwkw-stock-ecuturbo/) and they are making similar/more power and I have the Nistune.

Any replies are appreciated!

Cheers, Jacob

Link to comment
https://www.sau.com.au/forums/topic/451464-fmic-and-retune/
Share on other sites

If you're thinking of spending some money on a tune there's a couple of things you should do beforehand.

New fuel pump for safety more than anything. The stock ones aren't very good now that they're 20 years old.

Dial in some extra boost with the tuner. 10 pounds isn't a whole lot these days and you're not maxing out the injectors yet.

Edit: sorry I thought you said highflow turbo. You can't really go much higher than 10-12 psi on the stock turbo without risking damage

Edited by Blackkers
Link to comment
https://www.sau.com.au/forums/topic/451464-fmic-and-retune/#findComment-7438875
Share on other sites

If you're thinking of spending some money on a tune there's a couple of things you should do beforehand.

New fuel pump for safety more than anything. The stock ones aren't very good now that they're 20 years old.

Dial in some extra boost with the tuner. 10 pounds isn't a whole lot these days and you're not maxing out the injectors yet.

Edit: sorry I thought you said highflow turbo. You can't really go much higher than 10-12 psi on the stock turbo without risking damage

What would the stock injectors capable of?

Link to comment
https://www.sau.com.au/forums/topic/451464-fmic-and-retune/#findComment-7439038
Share on other sites

Thanks GTSTBoy, is GTR injectors a good upgrade?

won't fit on a GTS-t without some serious dicking about.. at about the same time you could convert to 21st century injector technology like what I've done here:

http://www.trak-life.com/diy-converting-top-feed-injectors-r33-gts-t-skyline-rb25det/

RB25DET-Top-Feed-01-1024x678.jpg

RB25DET-Top-Feed-25-1024x678.jpg

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/451464-fmic-and-retune/#findComment-7439589
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello! Long time lurker, been using the forums to address concerns and questions from afar for a while but I've struggled to find some answers so I guess its about time I made an account and formally asked some more knowledgeable people, since finding local skyline owners is hard (and shops that are knowledgeable or trustworthy to work on 'rare' cars are non existent out where im at, as skylines are quite uncommon to find in the wild around here). So the main 3 questions I have, 1: Steering rack has blown seals, well.. they kind of hold but they are not sealed properly anymore and as my R33 is my DD, i cant exactly rip the rack out and send it off or attempt to fix myself. As most refurb ones are around $1,100 or more shipped, and I have other things I need to work on around the car, I was seeking clarification on whether an S15 rack will more or less bolt right in, and whether a common mechanic could do any other required work to get it to fit. I ask, as I've found a supplier than can sell a manufactured as oem one for around 400, if not I'll likely order a used one from Jacks JDM, and take a risk on the seals there. The second question i have is that im replacing the front wiper cowl and have planned to buy 4 new clips and a new center clip but wasnt sure if there were any other clips that would also need to get replaced while I was at it. Given im sure any that are there now will simply break when I remove the old cowl... Last thing would be a fairly straight forward question, i think. If I manage (strong if, finding one has proven to be a pain) to find a R33 GTR spoiler/wing will it require much modification to bolt to a S2 R33 GTST? I've read the bolt patterns dont match but otherwise would bolt in, only options I have found with much luck is China stuff on ebay and carbonetics, which has a nice $650 shipping fee... so if anyone has any pointers where a US chap could locate one that would be great Random side question as well, the mirrors as I understand are mirror glass, and as im planning to polish my windows from water spots and surface scratches, i was hopeful cerium oxide would be fine for them too, as my research points to, but clarification is always nice. Any pointers would be appreciated, and while I have scoured the internet for answers if I missed a prior post somewhere that may answer these directly please point me towards it, as i must have simply missed it. I have seen a post here or there that has mentioned it, but I usually get 50-50 answers, or half answers... I dont have a lot of fab experience or mechanic experience, outside of hydraulic and pneumatic stuff I did in the military and with how hard it is to source stuff in the US, id rather not wing it and hemmoraghe money lol. Thanks guys! Sorry for the monumental first post haha
    • Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
    • Got you mate. Check your email!
    • I see you've never had to push start your own car... You could save some weight right now...
×
×
  • Create New...