Jump to content
SAU Community

Recommended Posts

Hi All,

I've had some recent issues with my series 1 R33 that has me thinking that the CAS is dying and needs to be replaced, however I'm looking for a second opinion before I go out and source a replacement.

It started running rough the other night on the highway randomly after driving for around 20 minutes. It was running low on fuel at the time, so as it runs on E85 I assumed it was possibly picking up some water/crud from the tank and limped it over to a mates house quickly. After filling it up with a jerry can of E85 about 30 minutes later, I started it up and gave it a rev and all was fine once again. I ended up driving it back home about 5 hours later and it didn't have any problems for the remainder of the drive (about 30 minutes).

Fast forward to yesterday and my old man takes it for a drive after its sat for a day or two and once again it runs fine for about 15 minutes then starts running really rough. I looked over it yesterday after its been sitting for about an hour and it's still running rough this time. I end up replacing the fuel filter just in case its clogged up and there is no change - fuel pressure at the rail is around 44psi which is spot on apparently and I cannot see any problems with the fuel system (has an E85 460lph Walbro installed). I move onto the spark plugs which appear to be fine and then check and replace the coil packs with known good spares to check that a coil hasn't died and it makes no difference (currently has ~2 month old yellow jackets). I then attempted to disconnect a plug for each cylinder to determine if there was a particular cylinder dropping but it doesn't seem to be any particular one. I also checked the ECU (Link G4+ plugin) which doesn't register any relevant error codes.

After another hour or so of checking lines, wiring, etc I start it back up and its now running worse than ever - barely idling and struggles to rev at all (feels like all the timing has been pulled).

Based on the above I assume its the CAS that's dying, however would love a second opinion/sanity check of the above!

TL;DR;

RB25DET running badly

Initially only happening after 10-15 mins of driving, now all the time

Have checked ECU, plugs, coil packs, fuel filter, fuel pressure

Assume CAS is dying and want a second opinion

Log your voltage with your ECU, see if the voltage drops as you drive in the higher rpm area.

I had a similar issue where my car would splutter and shit whenever it was warm.

Turned out my alterntor was cactus and voltage dropped to 12.2 volts after 4000rpm or so

So you have the software for the link on a laptop? I would start by looking at everything you can on the link software wbile while its having the problem. In one of the top drop down menus there is 'view parameters' or something along those lines which has a heap of tabs with all the stats of the car. Start with that

Have you done simple things like pulling individual coilpack plugs out while running to see if one doesnt change the engine note.

You can idividually check injectors in the link software. I think in aux outputs - fuel there is an injector test option

The link software is great for testing outputs. Can check whats working (options for test pwm or test that just turns it on)

Depends...I replaced a CAS on an RB25DET which was running rough. When we got the CAS off it felt like a stuffed wheel bearing - turned roughly and sometimes caught almost solid.

  • 4 weeks later...

For anyone that cares it turned out to be the ignitor.

I bought a replacement ignitor from a parts shop that was supposed to be "tested in working condition", but it seems it was just as broken as the one I had on. Workshop put a brand new one on and it runs perfectly now.

  • Like 2

Also FYI

I had the exact same issues on my 34.

34s ingiter is built into the coilpacks.

My issue was related to my injectors being blocked from E85 when i change my engine with a different fuel tank, same symptons as you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...