Jump to content
SAU Community

Recommended Posts

Hey guys I think I have found the cause of my car running rich all the time and eating fuel, can someone please confirm this... (ps I'm running a Power FC)...

So as I take it the actual full tune comes on at 80+ degrees celcius is this correct?

Well my car is barely ever over 80, normally sits around 75, if I give it quite a fanging it gets to 82 then as soon as I drive normally again it goes back down to the 70's range, would this be the cause?

Second question, if this is the cause... would it be because my water temperature sensor is faulty? or is my car just cooling way too much (which I highly doubt) all of the cooling system is still standard, stock radiator, fan, shroud... it's even got a front mount at the front of it which should block some of the cooling so I'm stumped...

Thanks for any help in advance, thanks.

Most likely the thermostat is stuck open.

You can check the ECU's temp sensor. It has a defined resistance at every temperature. Just look up (google) what it's supposed to be at the temperature it will idle at. Then just compare the measured resistance against what the ECU says the temperature is.

Edited by GTSBoy

Well when I go into settings and then water temp correction, 80+ is at 1.00 - 1.00 and the rest eg 50+ are higher so I'm asuming its to put more fuel and and advance timing?, probably does have a nismo thermostat, never really checked since I bought the car, will check it out tomorrow and also write down the actual figures for 50+ etc, thanks.

Most likely a Nismo thermosate, same issue I'm having ATM, the base map on my ECU start coolant multiplier from 75deg escalating as the temp gets colder on the scale, I have to change that as my car sits right on 70deg daily driving and gets upto 76-78 on the track due to the manual clutch fan starting to kick in

you are correct in your analysis that the PFC will assume a base of 1.00 at 80deg water temp +

you can either diag why your water is too cold or simply edit the 50deg+ correction and match it to the 80deg setting.

just be sensible with the car when it gets to around 50deg and ensure its properly warmed up before you flog it

Well I'll try adjust that and just put the 50+ at 1.00 - 1.00 correction and see how that goes coz I feel silly taking a nismo thermostat out and putting in a tridon or something haha lol... if I don't notice much difference then I'll change the thermostat aswell... i did also notice that it always idled a little lower and more power when I do get it to over 80 degrees lol and always wondered why... I will let yous know how I go both with power and fuel consumption.

Throw the Nismo thermo in the shit can where it belongs. Never could understand why anyone would want a colder thermostat. Worst bandaid EVAR!

Probably for track to have more flow? Beats me dude.

Why is this hard to understand ?

Having an engine that runs a little bit cooler is not a bad idea, especially when that coolant is running through the head keeping the combustion chamber temps down a touch

The only problem is fitting them to engines where the ECU can't be adjusted to run properly with them

Engines run better when hotter due to their tune, if your engine has been tuned to run at 85 deg with the engine temp multiplier starting at 80 deg and increasing down the colder scale then you try and run it at 70 deg then no wonder why it runs worse, set it up to run there and tune to run there and it will run there perfectly fine and further away you are from the detenation threshold, obviously you can't run an engine hard at 20deg but 70deg + would make no difference if tuned properly

How about putting a nissan thermostat in?

It may be that you have a normal thermostat and its not functioning properly. Wouldnt hurt to change it out. Only have to drain the coolant, take the 3 bolts for the thermostat housing out and change it

Fresh coolant wont hurt

New thermostat should only be $30 or so. Worth doing if you dont know when it was last done

Yeah I'm going to be doing that... been wanting to change my coolant for a little while now... last time coolant and thermostat were changed was when I had the car imported in 2011 and got the timing belt, water pump and all that done about 30000kms ago... what coolant do you guys recommend? Atm it's got some kind of purple coolant? I think it may be royal purples coolant? From what I've checked out so far I like the look of penrites coolant... although never used it before and unsure, what do you guys use and every how often do yous change it, thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
    • Yeah that looks like great caster, but I'd suggest trying less front camber some time and seeing if it helps with braking without reducing mid corner speed too much
    • I ended up setting the rear 5mm higher than normal to give some clearance.  My plan is to run the least camber I can in the rear which I think with the extra width is going to need to be -1.75 to -2.00° just to get clearance.  Guards have been rolled and pulled as much as they can/I would be wanting to.  front has the Acostal knuckle with the KPI change and the drop etc. So should be okay with the existing settings I have run with AR1s etc Front: Toe total -2mm(1mm out each side) Caster +7.5° Camber -3.8° Ackerman +15°
×
×
  • Create New...