Jump to content
SAU Community

Recommended Posts

Hi guys,

Here is an interesting one. I had the original spec wheels 225/45/18 & 245/45/18 on the before I upgraded them to a 19inch set-up (245/35/19 & 275/35/19). Recently I got a small cosmetic bend on the outer lip of the 19s and decided to put back my stock wheels.

Stock wheels go back on, and the traction control doesn't let the car accelerate and the SLIP light comes on. Car wont go more then 60-ish no matter how much the throttle is pressed. If I turn the traction control OFF, it is OK but I wasn't totally satisfied and went back to the 19s.

Any ideas on why this is happening and how to rectify it?

p.s. I had no issues when going to the 19inch wheels.

are you sure you put the 245s on the rear and not the front?

I swapped my wheels front/back to check if there were any clearance problems with 245 tyres on the front of my sedan and the VDC went nuts.

How long did you drive around with them on for? A couple of times what I have changed tyres size/profile dramatically and the it takes the VDC system 20 mins or so to learn, then it just turns the lights off and is all ok again.

are you sure you put the 245s on the rear and not the front?

I swapped my wheels front/back to check if there were any clearance problems with 245 tyres on the front of my sedan and the VDC went nuts.

Yeh I thought about that but I'm 100% sure they were on the correct ends.

How long did you drive around with them on for? A couple of times what I have changed tyres size/profile dramatically and the it takes the VDC system 20 mins or so to learn, then it just turns the lights off and is all ok again.

Actually not long at all, maybe only 2-3 mins then back into the shop to get them changed back. How did you drive 20mins? It hardly let me accelerate?.....It seemed ok when I turned it off (VDC).

How long did you drive around with them on for? A couple of times what I have changed tyres size/profile dramatically and the it takes the VDC system 20 mins or so to learn, then it just turns the lights off and is all ok again.

Yeah I heard something like that.

Yeah and a fewpeople have a problem when putting the car on the dino and it take a while for the car to set itself right again. Holding the VDC down for 10 sec might help.

Hi guys,

Here is an interesting one. I had the original spec wheels 225/45/18 & 245/45/18 on the before I upgraded them to a 19inch set-up (245/35/19 & 275/35/19). Recently I got a small cosmetic bend on the outer lip of the 19s and decided to put back my stock wheels.

Stock wheels go back on, and the traction control doesn't let the car accelerate and the SLIP light comes on. Car wont go more then 60-ish no matter how much the throttle is pressed. If I turn the traction control OFF, it is OK but I wasn't totally satisfied and went back to the 19s.

Any ideas on why this is happening and how to rectify it?

p.s. I had no issues when going to the 19inch wheels.

I think I know what the issue is...

You do not have the stock 18" tyre sizes fitted...

Standard 18" tyres are 225/50/18, not 225/45/18 on the front. With both ends being 45 profile on your car, there is a 3% difference between the front and rear wheels rotational speed and I belive that this is enough to trip the traction and stability control systems.

The fix would be to fit the correct 225/50/18 tyres on the front, or do what I did, and fit the same 245/45/18 tyres on the front rims. They do fit fine.

^^ Nah I had vastly different width wheels, tyres and type profile/rolling diameters from the rear for years - like I said previously, all you have to do is drive for 10-20mins or so and let the ECU figure out what is going on, and it all goes back to normal.

I think I know what the issue is...

You do not have the stock 18" tyre sizes fitted...

Standard 18" tyres are 225/50/18, not 225/45/18 on the front. With both ends being 45 profile on your car, there is a 3% difference between the front and rear wheels rotational speed and I belive that this is enough to trip the traction and stability control systems.

The fix would be to fit the correct 225/50/18 tyres on the front, or do what I did, and fit the same 245/45/18 tyres on the front rims. They do fit fine.

The stock sizes are 225/45/18 front and 245/45/18 rear. Even the tyre placard on mine shows this.

Same with the 19s. stock sizes are 225/40/19 front and 245/40/19 rear.

They are a staggered setup.. I think the 350Z might be the same??

Edited by sonicii

Ah sorry, my bad, I thought V36...

I guess the V35 has more robust handling of the diffrence in the wheel speed front to rear... I have seen this issue before with the V36s and it was the difference in tyre size that screwed the VDC system up..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...