Jump to content
SAU Community

<500cc Side Feed Injectors - Rb25 Neo

Linnertson

By Linnertson,
in Wanted to Buy

 Share

Recommended Posts

Linnertson Apprentice

Linnertson

Posted
  • Author
Posted (edited)

Oh really? I thought all 25's were side feed. I better have a look then :S Is there any real way to tell, will the injectors be litterly flat to the block if its a side feed?
Thanks fellaz.

I've gone from SR to RB and I know almost nothing about them yet :unsure:

Edited by Linnertson
Link to comment
https://www.sau.com.au/forums/topic/453996--/#findComment-7482755
Share on other sites
colourclassic Mentor

colourclassic

Posted
Posted (edited)

It's very easy to tell. On side feed rails the injector heads protrude past the rail and are retained with caps. On the top-feed rail of the Neo the injectors are retained by the rail i.e. the rail is the highest point.

The SR uses a side feed rail and it looks similar to non-Neo RB25's.

Edited by colourclassic
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/453996--/#findComment-7482907
Share on other sites
Linnertson Apprentice

Linnertson

Posted
  • Author
Posted

I checked just then and yep, looks like a top feed. I understand now because I know my old SR had the caps so that makes sence, thanks guys all this knowledge helps :)
I dont really plan to run E85 tbh, just because theres no one that close I would fill up on in the north shore (and I do weekly trips to newcastle).

Link to comment
https://www.sau.com.au/forums/topic/453996--/#findComment-7483403
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...