Jump to content
SAU Community

Recommended Posts

Car is gone so time to clean out all the parts. Prices negotiable and postage is at buyers expense from QLD. Contact via PM for more pics/info.

GTT Nistune package $550 – everything you need to get the most out of your bolt on mods. Never got around to installing this in my car, but all parts were purchased in working order.

R34GTT Manual ECU

Type 4 Nistune board and cable
Turbotech manual boost tee
Blitz 52mm mechanical boost gauge and cup
https://www.dropbox.com/s/zltyv6tx49ptvz6/2015-03-30%2020.48.21.jpg?dl=0

R34 plastic eyelids $80 – in sonic silver. Slight bend in one as per picture, does not affect ‘performance’. Affix with double sided tape.

https://www.dropbox.com/s/tbx9o9c0vok64k7/2015-03-28%2015.22.57.jpg?dl=0

R34 coupe front and rear standard bumper $120 for both – in sonic silver. Front bar is off a GT so no SMIC vent. Both in good condition with a few scratches from being in storage

https://www.dropbox.com/s/lwre91y656wf3qr/2015-03-28%2015.21.30.jpg?dl=0

R34 sub box $50 - fibreglass, moulded to fit corner of the boot. Small hole as per picture. sold pending

R34 coupe LED Tail lights $150 – same as these. All leds working when last fitted. Plug and play

http://www.ebay.com.au/itm/99-02-NISSAN-SKYLINE-R34-GTR-LED-Tail-lights-GTR-GTT-RB-/221143857491?pt=LH_DefaultDomain_15&hash=item337d337953

R34 GTT stock wheels $150 – gutter rash on most of the wheels. Average rubber.

R34 GTT stock coilovers $50 – cracked dust boots, came out of car with <100thousand k’s and were working fine

R34 GTT stock front indicators and side repeaters $80
https://www.dropbox.com/s/du7i20nmdwyb7zo/2015-03-28%2015.23.28.jpg?dl=0

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/455244-r34-parts-clean-out/
Share on other sites

What would you be after for just the Nistune board and cable?

PM me an offer, will have to be compelling to split up the pack

R34GTT Stock airbox and snorkel $100ono also available.

Edited by sonnyQ

Car is gone so time to clean out all the parts. Prices negotiable and postage is at buyers expense from QLD. Contact via PM for more pics/info.

GTT Nistune package $550 – everything you need to get the most out of your bolt on mods. Never got around to installing this in my car, but all parts were purchased in working order.

R34GTT Manual ECU

Type 4 Nistune board and cable

Turbotech manual boost tee

Blitz 52mm mechanical boost gauge and cup

https://www.dropbox.com/s/zltyv6tx49ptvz6/2015-03-30%2020.48.21.jpg?dl=0

R34 plastic eyelids $80 – in sonic silver. Slight bend in one as per picture, does not affect ‘performance’. Affix with double sided tape.

https://www.dropbox.com/s/tbx9o9c0vok64k7/2015-03-28%2015.22.57.jpg?dl=0

R34 coupe front and rear standard bumper $120 for both – in sonic silver. Front bar is off a GT so no SMIC vent. Both in good condition with a few scratches from being in storage

https://www.dropbox.com/s/lwre91y656wf3qr/2015-03-28%2015.21.30.jpg?dl=0

R34 sub box $50 - fibreglass, moulded to fit corner of the boot. Small hole as per picture. sold pending

R34 coupe LED Tail lights $150 – same as these. All leds working when last fitted. Plug and play

R34 GTT stock wheels $150 – gutter rash on most of the wheels. Average rubber.

R34 GTT stock coilovers $50 – cracked dust boots, came out of car with <100thousand k’s and were working fine

R34 GTT stock front indicators and side repeaters $80

https://www.dropbox.com/s/du7i20nmdwyb7zo/2015-03-28%2015.23.28.jpg?dl=0

Sub box and taillights gone, everything else available. make an offer

Edited by sonnyQ

Prices revised, willing to separate Nistune package. PM offers

GTT Nistune package $500 – everything you need to get the most out of your bolt on mods. Never got around to installing this in my car, but all parts were purchased in working order.

R34GTT Manual ECU

Type 4 Nistune board and cable
Turbotech manual boost tee
Blitz 52mm mechanical boost gauge and cup
https://www.dropbox.com/s/zltyv6tx49ptvz6/2015-03-30%2020.48.21.jpg?dl=0

R34 plastic eyelids $70 – in sonic silver. Slight bend in one as per picture, does not affect ‘performance’. Affix with double sided tape.

https://www.dropbox.com/s/tbx9o9c0vok64k7/2015-03-28%2015.22.57.jpg?dl=0

R34 coupe front and rear standard bumper $100 for both – in sonic silver. Front bar is off a GT so no SMIC vent. Both in good condition with a few scratches from being in storage

https://www.dropbox.com/s/lwre91y656wf3qr/2015-03-28%2015.21.30.jpg?dl=0

R34 GTT stock wheels $150 – gutter rash on most of the wheels. Average rubber.

R34 GTT stock coilovers $50 – cracked dust boots, came out of car with <100thousand k’s and were working fine

R34 GTT stock front indicators and side repeaters $50
https://www.dropbox.com/s/du7i20nmdwyb7zo/2015-03-28%2015.23.28.jpg?dl=0

R34GTT Stock airbox and snorkel $80

Also have an R34GTT AFM (pink label) in working order - $70

bump sat alone in a boggy marsh....

Will have access to wheels on Wednesday so will be bringing them to my house and posting pics.

All prices adjusted!


GTT Nistune package $450 – everything you need to get the most out of your bolt on mods. Never got around to installing this in my car, but all parts were purchased in working order.

R34GTT Manual ECU

Type 4 Nistune board and cable
Turbotech manual boost tee
Blitz 52mm mechanical boost gauge and cup
https://www.dropbox.com/s/zltyv6tx49ptvz6/2015-03-30%2020.48.21.jpg?dl=0

R34 plastic eyelids $60 – in sonic silver. Slight bend in one as per picture, does not affect ‘performance’. Affix with double sided tape.

https://www.dropbox.com/s/tbx9o9c0vok64k7/2015-03-28%2015.22.57.jpg?dl=0

R34 coupe front and rear standard bumper $90 for both – in sonic silver. Front bar is off a GT so no SMIC vent. Both in good condition with a few scratches from being in storage

https://www.dropbox.com/s/lwre91y656wf3qr/2015-03-28%2015.21.30.jpg?dl=0

R34 GTT stock wheels $150 – gutter rash on most of the wheels. Average rubber.

R34 GTT stock coilovers $50 – cracked dust boots, came out of car with <100thousand k’s and were working fine

R34 GTT stock front indicators and side repeaters $50
https://www.dropbox.com/s/du7i20nmdwyb7zo/2015-03-28%2015.23.28.jpg?dl=0

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Please use a modern ECU. PowerFC with the Nintendo Gameboy controller is horrible. It's not 2005 anymore.
    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
×
×
  • Create New...