Jump to content
SAU Community

Recommended Posts

Houston we have a problem ! ! !

After months of anticipation and a shit load of car preparation in the last couple of weeks (full fluid change, discs machined, new pads, seat and harness mounts improved and lots of little issues fixed including mounting a set of Pirelli wets on new rims just for the rain that is forecast) we were doing one of our system check runs yesterday to discover we now have a bearing failure.

Unlike most Skylines with bearing problems ours is in the turbo and it is making a hell of a racket as soon as it tries to come on boost.

In addition to the entry fee we have invested money in accommodation and van hire for the day (for all of our stuff) so we will still attend but will be in a hairdressers car (e.g. 4 cylinder daily). We will still have some semi's and wets to run on the car so if it is wet we still may be able to keep up with traffic in our respective groups.

See you on Monday.

Hey All,

Any suggestions on tyre pressures for a wet rainy coldish day?? Should it just be left normal or would you guys consider a change for this type of weather??

Im pretty sure my pathetically slim and cheap tyres are gonna struggle, need all the help i can get :0

Thanks

  • Like 1

Hey All,

Any suggestions on tyre pressures for a wet rainy coldish day?? Should it just be left normal or would you guys consider a change for this type of weather??

Im pretty sure my pathetically slim and cheap tyres are gonna struggle, need all the help i can get :0

Thanks

I was thinking the same thing!

Hey All,

Any suggestions on tyre pressures for a wet rainy coldish day?? Should it just be left normal or would you guys consider a change for this type of weather??

Im pretty sure my pathetically slim and cheap tyres are gonna struggle, need all the help i can get :0

Thanks

Leave them at normal pressure you would run on street then adjust as you go

Normally in the formula fords we run them a little higher, you think of it as an ice skate, you want a nice edge to cut through standing water ect. If only damp you normally run them on a preassure you are aiming to get to when fully warmed up in the dry.

So if in the dry you want your tire temps at 25psi and normaly to get that you would start at 23psi, you would just start them at 25psi and check when car returns from session and bleed until you hit that 25psi.

Also my daily will be used. My 200kw R33 so hoping to crack a 10 if not to went considering my underpowered R32 gets mid 15's

ECU never turned up. See you all there

Hey All,

Any suggestions on tyre pressures for a wet rainy coldish day?? Should it just be left normal or would you guys consider a change for this type of weather??

Im pretty sure my pathetically slim and cheap tyres are gonna struggle, need all the help i can get :0

Thanks

Not sure what sort of tyres you have, but I'd put at least 40psi cold in there. You can always let air out.

Not sure what sort of tyres you have, but I'd put at least 40psi cold in there. You can always let air out.

Hey Mate,

This sounds like the way to go, especially considering Calsonic14u's comments.

fyi, ive got Gemstone 215's all round, on17's. I know what you're thinking....wtf, wat a noob. But they came with the car and like 95% tread so i thought id rpi them up quick then upgrade. Never anticipated the rain though :no:

Lol DW im running a second hand set of Pirelli on the rear and Re001 on the front on 17s atm on my daily, needless to say i wsnt planing on running her tomorrow lol.

my tires are set atm at 36psi all round, probably wont be bleeding at all haha. dont even think im taking tools :P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
    • This. The R34 handbrake icon DOES come up when the brake fluid level is low. You might be sitting right on that threshhold. I have been down this diagnosis path and this was the solution (and it was pretty much as full as your picture is to begin with).
    • Unfortunately the cavaet to that is that while any scan tool should be able to read the code, the workshop will need a consult plug to OBD socket adapter. You don't have a location on your profile, where are you based?
    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
×
×
  • Create New...