Jump to content
SAU Community

Rear Lock / Hand Brake Or Rear Brakes In The Morning

INSANITI
 Share

Recommended Posts

INSANITI Collaborator

INSANITI

Posted
Posted

Hi All,

As soon as I got home last night I cleaned my wheels, using light soap and luke warm water. I then parked the car in the garage. This morning when I was driving it out of the garage the rear (more passenger size rear) felt like it has locked up. it doesn't feel like its the foot (hand) brake it felt like the brakes got stuck to the brake rotors. I don't put a lot of pressure on my foot brake so I doubt its that. I had to add a bit of acceleration as I reverse to force it to release. it seemed to work and I drove to work no problems.

take note that after hosing the brake rotors it gets a bit rusty looking (slight squeak as you brake)

has anyone experienced this before?

are there pads in the footbrake (handbrake) that needs replacing?

thanks

sonicii Veteran

sonicii

Posted
Posted

happens to me every time I wash my car and park it back in the car port. isn't major and doesn't require much extra effort to get the car moving, but it makes a 'cluck' sound when it lets go. I just assumed it was a bit of corrosion between the rotor and the pads from the water.

Pads in the handbrake (Foot brake) shouldn't need replacing if you don't drive with the handbrake on.

mkn23 Collaborator

mkn23

Posted
Posted

yeah i get kinda loud clunks in changing gears when it's cold, if warm the clunks sound normal and fine

my driveway is on a slight slope so maybe that's why also and i always get the clunking sound from the brakes every morning

The Max Mentor

The Max

Posted
Posted

And while we're talking about parking brakes, despite having had them professionally adjusted, I still don't have a lot of confidence in the grip of the parking brakes. I'm going to take the rears off and inspect them soon but I'm thinking it might be worth considering a better pad or at least a new set in the event they're just worn away from perhaps a careless previous owner who drove with them on for a bit now and then? :)

  • Like 1
INSANITI Collaborator

INSANITI

Posted
  • Author
Posted

I always wondered why Nissan put a foot park brake instead of the normal hand brake.... once I drove 50 metres of it on hahaha!

Anyhow its good to have raised this I don't think this has been raised before. I was sh1ting my pants thinking it would lock up while I was driving hehehe..

sonicii Veteran

sonicii

Posted
Posted

I always wondered why Nissan put a foot park brake instead of the normal hand brake.... once I drove 50 metres of it on hahaha!

Get a 6sp manual.. it has a hand brake! :)

  • Like 1
t5iv Grand Master

t5iv

Posted
Posted

Autos have the foot brake to allow more space in the centre console and a more smooth surround. Can't have pedal park brake on a manual so that's why they have handbrakes.

Flecks of rust spots on your rotors are nothing to be worried about. Drive normally and it will wear away.

  • Like 1
INSANITI Collaborator

INSANITI

Posted
  • Author
Posted

Get a 6sp manual.. it has a hand brake! :)

I wish I did now. I was in awe when I saw the first skyline I viewed and due to having gout problems back then I figured a semi auto is good enough and pulled the trigger on my 2005 coupe. hehe

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...