Jump to content
SAU Community

Recommended Posts

There isnt a whole lot of info on rb30dets in my desired relms of use. Most rb30dets area drag monsters...

Hmm suppose it's the difference between a punchy quicker less laggy spool or a wait for a bit and get the the the holly f##k on it scary spool. Response vs shear power balance. Loads of rb's you see with bigger turbo's tend not to be able to get off the line or blow up boxes half shafts and diffs. I'd say with the bigger turbo you would need a mental clutch and longer ratio to get the power happening or it would just snap stuff and light up the tyres permanently. Which is also fun:-)
6 minutes ago, TiTAN said:

 


High flows have been tried on an rb30 years ago. It was a cheap build basically stock Na bottom end with the 25 head and it came on like a light switch but come 5000 it hit a wall, by 5500 it had dropped about 100kw from memory.

 

This is no gd... mine will be a forged bottem end so looking to lean on it some ?


Hmm suppose it's the difference between a punchy quicker less laggy spool or a wait for a bit and get the the the holly f##k on it scary spool. Response vs shear power balance. Loads of rb's you see with bigger turbo's tend not to be able to get off the line or blow up boxes half shafts and diffs. I'd say with the bigger turbo you would need a mental clutch and longer ratio to get the power happening or it would just snap stuff and light up the tyres permanently. Which is also fun:-)

Being a 3ltr it will have more torque anyhow so perhaps response is the way to go? Don't forget I'm only a sheet metal worker who has never blown up a Cleavo Windsor c4 top loader or 9".[emoji4]
Gtx3582r with an 50mm external gate is what i was also thinking. Either way i think external gates gonna be better


I had a pre gtx series 35r with 0.82 rear. If you tweaked the waste gate setup you could have 20psi at 3500. Traction was non existent below 100km/h, for Street use it was too laggy to be quick and too fast to be usable without potential jail time. You would start seeing positive boost (a few psi) at 2500 with a bit of load.

Guilt-toy had a similar setup and should be documented fairly well on sau.

This is my dyno sheet, 26 psi and the dip at 145 was spark breaking down, done on a 33c day.

IMG_1502280990.305269.jpg
13 minutes ago, Beyond Blue R33 said:


Being a 3ltr it will have more torque anyhow so perhaps response is the way to go? Don't forget I'm only a sheet metal worker who has never blown up a Cleavo Windsor c4 top loader or 9".emoji4.png

I hear u can get cheap pipe? Gonna need some mikd steel and aluminium to make some pipe work. Proberly not till later in the year tho

  • Like 1
9 minutes ago, TiTAN said:

 


I had a pre gtx series 35r with 0.82 rear. If you tweaked the waste gate setup you could have 20psi at 3500. Traction was non existent below 100km/h, for Street use it was too laggy to be quick and too fast to be usable without potential jail time. You would start seeing positive boost (a few psi) at 2500 with a bit of load.

Guilt-toy had a similar setup and should be documented fairly well on sau.

This is my dyno sheet, 26 psi and the dip at 145 was spark breaking down, done on a 33c day.

IMG_1502280990.305269.jpg

 

Hell yeah, that looks right up my street. I wont be using it much on the street, mabe once a week at this stage. Il proberly get hooked at drive it all tje time lol

thats a run out at an airport, i am not even an amateur film maker obviously as its hard to even read any of the gauges. had spark breaking down at 160 then it clears up and keeps going, trapped at 242km/h at the 800m mark.

  • Like 1
6 minutes ago, TiTAN said:

thats a run out at an airport, i am not even an amateur film maker obviously as its hard to even read any of the gauges. had spark breaking down at 160 then it clears up and keeps going, trapped at 242km/h at the 800m mark.

Sounds gd ?

16 minutes ago, TiTAN said:

That's mainly to give you an idea just how quickly 400kw puts on speed.

If it's going to be a track toy, you are going to need some serious brakes to deal with stopping it. Upgraded pads and rotors won't cut it.

350 all round. Alpha omega brembo upgrade. Dba discs and bendix pabs. With all my cars its always been suspension, tyres, brakes then power.


Posted some pics of the boot fit out. What do you think of it?

Looks good mate, should sound good too.

A lot of bass is lost through the back seat of our skylines due to the steel plate etc but will still be plenty of punch no doubt.

Is it all hooked up and running now?
  • Like 1



  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...