Jump to content
SAU Community

Recommended Posts

Hey guys, did a parasitic current draw on my R34GTT- mounted multimeter in series to battery by removing -ve terminal and connecting to the terminal on battery and removed -ve terminal on wire.

Pulling fuses one by one revealed that the audio circuit is eating 0.15ish Amps or 150mA with everything off/doors closed etc for few mins. Current draw should not be more than 50mA. Without fuse it is 50mA, still a bit high. All fuses on, current draw is 0.2-0.18A. (180-200mA)

All it has is a basic Sony MOSFET cd player, standard speakers n tweeters, twin 6X9s in rear shelf, no amps or subs. Basic system. Removing/cutting audio power wire brings the current draw back to 50mA so thats the culprit.

What to do from here? Is it likely a short in audio power wire or a malfunction in unit? Thanks.

post-49401-14318186742917_thumb.jpgpost-49401-14318187117645_thumb.jpgpost-49401-14318187438_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/456681-parasitic-current-draw/
Share on other sites

When you say the current draw is 150ma for a few minutes, does that mean the current draw disappears?

It is probably just some sort of storage function of the head unit if that is the case and I wouldn't worry too much about it. I've never been a huge fan of the Sony car audio products, and I don't think they are the best out there. So i suppose if you really want to fix the problem you will probably need a new head unit. That is unless their is something else tee-ed into the audio circuit. Really the head unit controls all the power going to speakers etc, so if there is a current draw there it can only really be the head unit (unless, as I said there is another system on the circuit)

You got me wrong, I meant that the current draw is always 180-200mA even AFTER a few mins with everything off/doors shut etc. I stated the 'few minutes' because some car systems like alarms etc take a few minutes to fully shut down.

I dont think theres anything else tee'ed onto the audio circuit though, the factory loom with green power cable goes right up to the radio. I was thinkin its either the head unit or the power supply cables shorted somewhere in the loom.

Whats the best way to check, I've already wired direct power from battery to fuel pump via a 30A fuse and extra wire to battery. Can I tee a wire off this to the head unit?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...