Jump to content
SAU Community

Recommended Posts

these are the parts that i have left no reasonable offer denied

rear bar grey in colour bit faded $40

reinforcement behind rear bar $15

front seats out of m spec immac $300

rear seats out of m spec $90

grey carpet $40

grey hoodlining $30

fuel tank with fuel pump and sender $50

rear window $100

left hand quarter window with rubber $50

rear sub frame with hubs & control arms SOLD

gts4 or gtr front hubs control arms and struts $80

ac compressor $40

manual tail shaft $40

all plastics from center console and radio facia

brake master cyl with pipes and abs unit $100

A PILLAR TRIMS $25 EACH

LH POWER MIRROR $40

complete top end rb20det head, manifolds, turbo wiring, computer asking $400

no gearbox

no coils or ignitor

no dash or vents

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/
Share on other sites

is the boot charcoal metalic or gray as described???

Also do you have the metal lining that goes around the rear windo its a three piece metal strip thing???? PM me your mobile and i can have a chat about some stuff and prices!!!

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-931254
Share on other sites

Need 2 x o2 sensors out of GTR r32 , the ones that scew into dumps , must be working please.

these are the parts that i have left no reasonable offer denied

boot lid imac with wing off m spec gray in colour $90

rear bar grey in colour bit faded $30

rear seats out of m spec $90

both doors with all internals and glass . no door trims $200

grey carpet $40

grey hoodlining $30

fuel tank with fuel pump and sender $50

rear window $100

rear sub frame with hubs & control arms $80

gts4 or gtr front hubs control arms and struts $80

ac compressor $40

manual tail shaft $40

complete top end rb20det head, manifolds, turbo wiring, computer asking $400

no gearbox

no coils or ignitor

no dash or vents

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-931497
Share on other sites

these are the parts that i have left no reasonable offer denied

no gearbox

no coils or ignitor

no dash or vents

What about the underbody plastic bit RHF Guard - protects the BOV are from road dirt?

Odd screws/connectors from the bumper etc?

R32 GTR not sure if other cars are different

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-934827
Share on other sites

Hey man if you know if the R32 drivers side window is the same as an R33 and in good condition send pic if possible i'll take it plus its internals $130 and i'll front the shipping.

PM me. thanks

i'd say it would be different

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-939147
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...