Jump to content
SAU Community

Recommended Posts

I am currently running a 48mm progate and since fitting the 6870 it will not hold boost at the track.

It held it on the dyno with slight creep after 6000rpm but at the track I'm hitting boost cut in first no matter how low I set the eboost.

Has anyone done the straight swap for a 50mm? Will it hold it ya reckon?

Or will I have to get a 60mm and do a cut and shut job on the exhaust manifold?

Link to comment
https://www.sau.com.au/forums/topic/457965-48mm-vs-50mm/
Share on other sites

Want it to hold 30psi for 700hp (on dyno we had it set at 28 and it crept late then ignition break down at 7200)but as stated at the track I had it set 20 points lower on the eboost and it still hit 32psi as soon as it could in first gear.

60ft in 1.34. Was like a boost line was off.

Link to comment
https://www.sau.com.au/forums/topic/457965-48mm-vs-50mm/#findComment-7562021
Share on other sites

Try a much stronger spring first - as near as possible to target boost is better. Set your boost cut a bit higher. Does it overboost in the other gears (apart from 1st)? If you can borrow a 50mm W/G that would be worth a try but if you have to buy one I would go straight to 60mm.

Link to comment
https://www.sau.com.au/forums/topic/457965-48mm-vs-50mm/#findComment-7562108
Share on other sites

If a boost line was off it may have hit over 60psi, mine did.

Not sure about the gate you have, but Turbosmart had to re-design their spring caps to hold that boost. They made a much taller cap with springs 3 times as long, so the stiffer springs wouldn't limit the travel of the gate.

If you hit the soft limit at the track, that would cause overboosting no matter what the controller was set to.

Link to comment
https://www.sau.com.au/forums/topic/457965-48mm-vs-50mm/#findComment-7562133
Share on other sites

Interesting Scotty that sounds promising for the 50.

Jet I would just get the 60 but it's a manifold off job, which I will do if I have to but I'm sure ive read plenty of people having success with the 50 so just chasing feedback. So easy to just bolt the 50 on and go racing. 60 is a major for me at the moment.

Thanks for the feedback.

Link to comment
https://www.sau.com.au/forums/topic/457965-48mm-vs-50mm/#findComment-7562260
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...