Jump to content
SAU Community

Recommended Posts

Next Financial Yr Forecast (depending on Japanese auction results - depending on supply and demand)(kept at Grade 4B standard):-

* Non V-Spec - down 7%

* V-Spec - down 4%

* M-Spec - static

* V-Spec II - up 2%

* V-Spec II Nur - up 5%

* M-Spec Nur - up 7%

* V-Spec N1 - up 8%

* V-Spec II N1 - up 10%

** 'Tis my own time capsule for observation purposes Lol

*** As cars get older, the spectrum of quality gets wider

**** I hope there's no GFC 2.0 or oil embargo to fark this all up Lol

  • 2 weeks later...

If the fed government changes the import rules later this year I can really see BNR34 and other cars tanking in price. Instead of the 16 year old R34 I guess lot of people will just get the R35 for 50-60K.

  • 4 weeks later...

I'm going nuts over this same issue :wacko: . I miss my GTT too much so I've been looking at a 34GTR vpsec for the last few months.

Last option is to import one.. But as you guys can imagine I'm gettin a lot of resistance from family and friends saying dont spend so much on an old car.

Also I heard rumours about govt dropping import duties since the aus car manufacturers are shutting down their plants.

Will the 34GTRs retain their value? How much should I be spending on a clean one? I'm only lookin at V-spec and above. Preferably blue. :woot:

I know this is a month-old post but I thought I'd share my experience.

I was in the same boat as you, it was really difficult to find the perfect 34 GTR locally. I wanted a V-Spec or better, low km example, and it had to be blue. I gave up looking and contacted Ben over at J-Spec to get the ball rolling on an import. It was a tough decision to make at the time, but looking back it turned out to be 100% the right move. It can be daunting when you have to wait 3 months to take the car home, not to mention having to send tens of thousands of $ overseas, but with a good importer they'll make the process so seamless that you stop worrying pretty quick.

Long story short, I now have an immaculate grade 4.5 Bayside Blue V-Spec, with 37,000 genuine km complete with a full service history (I'm talking every single service sheet since brand new). It cost me around $56,000 landed and complied which I thought was very fair considering I knew of 3 similar examples that sold locally during my wait time for $60,000+.

Big shout out to Top Secret Imports here in Sydney as well, they made an otherwise painful compliance process super bearable. Awesome guys to deal with.

  • Like 1
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...