Jump to content
SAU Community

Recommended Posts

Hi All,

I have a bit of an issue I can't put my finger on and I am hoping the SAU community can help.

I recently imported a 33 GTR and when I drive the car and keep it at a steady 3500 rpm there's a miss. Below and over 2500 rmp the car runs ok. Having said that the fuel consumption is very bad and there's plenty of back fire in normal driving.

I have done my home work and searched on this site and Google and the below have been helpful but not solved my issue.

What I have done:

  • Changed spark plugs to NGK BCPR7ES which I chose after reading a thread on SAU
  • Changed the fuel filter
  • Changed the CAS
  • Changed the pod filters to airbox
  • Changed AFM
  • Changed BOV's and checked piping was on tight
  • Changed the coil packs and sealed them with dielectric goo as the YouTube video suggested

The car sounds a little rough on idle but I am not sure if this is because the cam timing as the in was set to 0 and ex 2 degrees retarded. I noticed this when I did a full service on the car and I changed my timing belt. HKS cam gears came as a surprise. (the car was missing before the service)

The only thing I haven't changed is my injectors and fuel reg as one of the topics said that possibly could be the issue.

Before I start removing the fuel rail, injectors and reg is there anything else that could be causing this issue?

All your input will be greatly appreciated as I am stumped!

Thanking everyone in advanced.

Link to comment
https://www.sau.com.au/forums/topic/458193-r33-gtr-missing-at-3500rpm/
Share on other sites

Most likely a vacuum/boost leak.

Last time i had a miss it was the igniter module, in my case it was above 3500 but sounded like the wide spark gap or faulty coil pack issue.

In your case with backfire it sounds more like a Vacuum or boost leak, you need to check your hoses and pipes first.

Thanks guys!

I think you might be right about the vacuum leak as I believe the brakes are not as good as they should be. I have found a workshop that has a vac leak tester (think it's called a smoke test) and have a booking on Monday.

Having said that though I used carby cleaner and sprayed around hoses but I didn't notice anything.

Will keep you posted on the results/ solution.

Edited by manage13

Dead or failing o2 sensors do all those things...

Hi Trent,

Thanks for your response. Does the engine light come on when an 02 sensor fails? Currently I don't have the warning light. Also, if I plug a diagnostics tool will I be able to tell if the O2 sensor is failing?

Thanks.

.. r33 GTR missing at 3500rpm!

2 questions:

- Where did it go? I assume it came back/

- Do you have a picture of the flux capacitor install?

Cheers

Justin

LMFAO! :yes: I'll pay that one.

Just unplug them and see if the miss is gone. This is called open loop.

Oh I already did this a few weeks ago and the miss was still there. :unsure:

Thanks guys!

I think you might be right about the vacuum leak as I believe the brakes are not as good as they should be.

What do you mean by brakes not as good as they should be?

As in making hissing (or bubbling) noise when it comes to complete stop as you'd felt on the pedal?

  • 3 weeks later...

Do the brakes get better with a few hard stops or do they fade? It is worth changing your brake fluid (any new fluid but something like Motul best). Otherwise a change of pads might be indicated. They could be track pads which don't pull up well when cold or they could be just rubbish pads (have a read of the brakes section for some suggestions) - I bought Pagid but they are quite expensive and there are other types that people like.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...