Jump to content
SAU Community

R33 Gtr Missing At 3500rpm

manage13

By manage13,
in Engines & Forced Induction

 Share

Recommended Posts

manage13 Proficient

manage13

Posted
Posted

Hi All,

I have a bit of an issue I can't put my finger on and I am hoping the SAU community can help.

I recently imported a 33 GTR and when I drive the car and keep it at a steady 3500 rpm there's a miss. Below and over 2500 rmp the car runs ok. Having said that the fuel consumption is very bad and there's plenty of back fire in normal driving.

I have done my home work and searched on this site and Google and the below have been helpful but not solved my issue.

What I have done:

  • Changed spark plugs to NGK BCPR7ES which I chose after reading a thread on SAU
  • Changed the fuel filter
  • Changed the CAS
  • Changed the pod filters to airbox
  • Changed AFM
  • Changed BOV's and checked piping was on tight
  • Changed the coil packs and sealed them with dielectric goo as the YouTube video suggested

The car sounds a little rough on idle but I am not sure if this is because the cam timing as the in was set to 0 and ex 2 degrees retarded. I noticed this when I did a full service on the car and I changed my timing belt. HKS cam gears came as a surprise. (the car was missing before the service)

The only thing I haven't changed is my injectors and fuel reg as one of the topics said that possibly could be the issue.

Before I start removing the fuel rail, injectors and reg is there anything else that could be causing this issue?

All your input will be greatly appreciated as I am stumped!

Thanking everyone in advanced.

Link to comment
https://www.sau.com.au/forums/topic/458193-r33-gtr-missing-at-3500rpm/
Share on other sites
GTRPSI Mentor

GTRPSI

Posted
Posted

Most likely a vacuum/boost leak.

Last time i had a miss it was the igniter module, in my case it was above 3500 but sounded like the wide spark gap or faulty coil pack issue.

In your case with backfire it sounds more like a Vacuum or boost leak, you need to check your hoses and pipes first.

manage13 Proficient

manage13

Posted
  • Author
Posted (edited)

Thanks guys!

I think you might be right about the vacuum leak as I believe the brakes are not as good as they should be. I have found a workshop that has a vac leak tester (think it's called a smoke test) and have a booking on Monday.

Having said that though I used carby cleaner and sprayed around hoses but I didn't notice anything.

Will keep you posted on the results/ solution.

Edited by manage13
manage13 Proficient

manage13

Posted
  • Author
Posted

Dead or failing o2 sensors do all those things...

Hi Trent,

Thanks for your response. Does the engine light come on when an 02 sensor fails? Currently I don't have the warning light. Also, if I plug a diagnostics tool will I be able to tell if the O2 sensor is failing?

Thanks.

manage13 Proficient

manage13

Posted
  • Author
Posted

.. r33 GTR missing at 3500rpm!

2 questions:

- Where did it go? I assume it came back/

- Do you have a picture of the flux capacitor install?

Cheers

Justin

LMFAO! :yes: I'll pay that one.

Just unplug them and see if the miss is gone. This is called open loop.

Oh I already did this a few weeks ago and the miss was still there. :unsure:

Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

Thanks guys!

I think you might be right about the vacuum leak as I believe the brakes are not as good as they should be.

What do you mean by brakes not as good as they should be?

As in making hissing (or bubbling) noise when it comes to complete stop as you'd felt on the pedal?

  • 3 weeks later...
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Do the brakes get better with a few hard stops or do they fade? It is worth changing your brake fluid (any new fluid but something like Motul best). Otherwise a change of pads might be indicated. They could be track pads which don't pull up well when cold or they could be just rubbish pads (have a read of the brakes section for some suggestions) - I bought Pagid but they are quite expensive and there are other types that people like.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...