Jump to content
SAU Community

Recommended Posts

so i had my car retuned a few weeks ago and the tuner noticed oil temp was consistantly high.

when it was last tuned and driven oil temp would sit at 80 degrees and now it sits between 90-100 when cruising at 100kph.

before the tune i switched from motul turbolight to penrite racing 10 10w40 and tidied up oil cooler (flipped how i installed it and moved temp sensor in line)

once the car has sat off for 10-15mins oil temp is back to 65-70.

engine:

built rb25 (2000km old, built by red r racing about 4.5 yrs ago) 6boost, gt3076 .82ex, greddy plenum, 1000cc xpurts.

nitto oil pump, rb20 oil block, mocal thermostat oil block (group buy kit), 19row setrab oil cooler (sits behind a opening in front bar), z145a filter

tuner has told me to use a thicker oil to see if that will solve the problem but i can't see how its gone from running normal to hot.

could there be another issue or changing the oil type will make that much difference?

and what oil should i try next? looking at penrite hpr10 10w50 or go back to motul?

What does your water temp do? Does your oil temp go nuts when you push the car hard? What does your oil pressure say at cruise? Always use Motul 10W 30 myself - if nothing else it can stand the heat .

Where have you moved the temp sensor from and too Rob?

The fact that youve played with the oil cooler and temp sensor makes me think either something is not right, or the temp sensor has moved from post cooler to pre-cooler

Sounds like it could be a plumbing problem. At cruise the oil shouldn't be getting hot enough to open the thermostat to send oil to the cooler. How have you got the cooler orientated in relation to the oil lines and are you sure the thermostat is plumbed correctly?

Where have you moved the temp sensor from and too Rob?

The fact that youve played with the oil cooler and temp sensor makes me think either something is not right, or the temp sensor has moved from post cooler to pre-cooler

This

Cal it's in one of the oil lines, just removed some of the adaptors I was using.Will swap it to the other line and see if there is a difference.

Oil cooler is mounted with inlet and outlet facing up. I rotated the oil block 90 degrees so fitting now faces downward and thermostat is horizontal.

Will remove the thermostat and check. Oil is getting to the cooler as it is getting hot.

Edited by robbo_rb180

If it is a temp issue (as opposed to sensor/gauge ect), picking up a bearing can result in high oil temps at low rpm/load.

Post some pic's of the oil cooler set up.

Cheers

J

Edited by XRATED

either would I, but IF he's is getting hotter than usual oil temps- just cruising...

I agree, it's more than likely a gauge/sensor re-location change that is displaying different temps.

I run the same oil (Penrite 10w40) and my oil temps sit at 70-80 when cruising and giving it stick on the road and only hits 90-100 when on the track. This is in Darwin heat too so could be more than likely gauge/sensor

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...