Jump to content
SAU Community

Recommended Posts

http://www.sau.com.au/forums/topic/309538-running-r34-gtr-on-2wd-dyno/

Last post.

"Unplug the Pump and bleed the slave on the transfer case. Takes a few minutes and works fine. "

Looks like removing the front shaft is OK though, i had misread it.

Edited by ActionDan

Love the ztune guards.

Would look much better with more sensible exterior bits also those mirrors look dope

yeah about $10k off stock can get to 300.

Id still consider 10k more on top to get it to where you want it, it seems.

His latest comment to some more of my questions.

"Tyres are pretty much new there only acchiels. Ive replaced all rotors and pads still like new when I did the rear rotors I also did the rear wheel bearings there was a little play in the left. And I had the boot split on the front driver side so I replaced both sides full cv drive shaft. A little extreme but I like the car perfect. Yeah I had the rims professionally painted. There's no stickers on them but theres raised embossed volk etc the cats and front pipes are done as well. And Ive never done a compression test. Your welcome to though"

Car is completely stock, has Nismo exhaust and front pipes but standard dumps :(

- Standard Dump Pipes can handle over 300+ rwkw's

So that's what... another 10k in mods to get it to 300+rwkw?

- No, if the engine is still tight and has a good compression, -7's or -9's / Cam Gears / 3" Exhaust / Nistune (R32 / R33) or PFC and Tune = 300 rwkw's.

Maybe not that bad given I can do the labour myself - not the tuning.

EDIT: Looks like prices have changed a bit and it's not that expensive to get 300-330 on 98.

-7 or -5s

- Go -7's, if you want 330 rwkw, you'd go -9's.

Injectors, Fuel pump, Cam gears

- Stock Injectors and Fuel Pump can handle 300+ rwkw's and get Racepace to modify you stock Cam Gears to be adjustable.

Cams not necessary but would help (and sound lovely) - No need but if you got money to spend, go for it...

PFC and tune - Yes

Full exhaust, some conjecture on 3 or 4"

- 3" for 300 rwkw's

- 3.5" for 350 rwkw's

- 4" for 400 rwkw's

AFMs - Stock AFM's are fine for 300 rwkw's

Standard intercooler and airbox fine. - Yes

Just so you know :)

  • Like 3

Re exhaust is that 3.5" all the way? I think ideally I'd like to go -9s and aim for more like 320-330ish with cams for response.

I was planning to get some 600-700cc injectors and a drop in fuel pump just for safety. I actually thought Z32s were a must at that level?

Re the car, discussion with the owner continues and is looking semi promising.

Waiting to hear back from the Jap history check, baring that having some nightmare info I will aim to get up there next Monday to inspect. My partner is away all this weekend coming (so I'll have the kidlet) so that's out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...