Jump to content
SAU Community

Recommended Posts

Hi everyone. I searched but couldn't find anything similar to my problem.

I am trying to clean years of grim, water marks and light corrosion off my wheels. They are Enkei Winsome 3 piece wheels and have a lot of bolts that I am having trouble cleaning around. I have successfully used some metal polish to clean the dish part of the wheel and using a clay block and paint cleaner on the painted middle section of the wheels, but I am struggling to clean the water marks/corrosion around the bolts.

Has anyone got any tips?

I was thinking about removing 1 bolt at a time and cleaning that spot, replace bolt and repeat.

Is this safe?

Should I get the wheels re-balanced after I do this?

What torque for the bolts?

Am I making this more complicated than it needs to be?

Here a a few pics (I hope this works)

Corrosion/Water Marks around bolts

wheel%20bolts.jpg

Wheels before cleaning

wheel%20dirty.jpg

Wheel now.

wheel%20clean.jpg

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/459727-cleaningrestoring-3-piece-wheels/
Share on other sites

Before you take the bolts out you can try with a dremel with an extension, polishing head and some metal polish and see how you go. If no good then yes you can take a couple of bolts off at a time. You can always check the torque with a manual torque wrench when you take them off. Then use the dremel to polish it.

Its a prick of a job but well worth it.

Edited by XGTRX

Thanks Guys,

I am going to pull the wheel off the car tonight, sitting hunched over on cold concrete for 3 hours last night killed my back.

I will try with the dremel with the bolts still in first but I think it is going to be harder than removing a bolt or 2 at a time then cleaning/polishing by hand.

I will post up pics when I am done.

Trex - To get them to the stage they are now I have just used Autosol Metal Polish with a tennis ball wrapped in a microfibre cloth, the tennis ball made it easy to do the dish part of the wheel. http://www.supercheapauto.com.au/online-store/products/Autosol-Polish-Metal-350g.aspx?pid=345178#Recommendations

However, my wheel are raw alloy, no clear coat or anything. From the reading I have done online, clear coat on some wheels is really hard to cut and polish but it can be done.

For the painted middle section I have used Meguires Ultimate Compound. It is awesome stuff, cleaned up and and removed really deep scratches in the paint on my Patrol. http://www.supercheapauto.com.au/online-store/products/Meguiar-s-Ultimate-Compound-450mL.aspx?pid=214309#Recommendations

I will check out the polishing BBS RS videos tonight.

Cheers.

  • Like 1

Small update of what I got done tonight.

I tried removing 2 bolts at a time but it wasnt working very well, I let all the air out then took out 4-5 bolts at a time. Screwed around for hours before I worked out a quickish way to do it. Takes about 45nm of torque to undo the bolts so I am tightening them back up to 40nm because I figure it takes a bit extra to crack the bolt. I have decided I will get them rebalanced and checked when I am finished just to be safe.

Cleaned loose crap off with Shellite, then cleaned off the chunky corrosion with a tiny steel brush dremel attachment by hand (not in the dremel) then polished by hand the remaining scuff and marks etc with the metal polish. Cleaned up the head of the bolts with a polishing attachment in the dremel with metal polish.

It is going to take forever (took 5 hours to do about a third of the wheel) but I am really happy with the result.

Before

bolts%20before.jpg

After

bolts%20after.jpg

The wheel so far.

third%20done.jpg

  • Like 5

spent about 4 hours on mine today, arm about to fall off

has anyone dealt with deep pitting in the aluminium? i can sand it all out but some it is fairly deep and dont want to take too much material off

I have finished one of the wheels. It looks good but I am not happy with the centre.

I have decided to go all out of the next wheel. I was thinking about getting the centre electrplated (either chrome or a satin finish) but first I am going to try polishing it myself.

I completely dissasembled the wheel this time. Used paint stripper on the centre then polished up a section to see how it would look, I think I am going to be able to get it to a level I am happy with. If I cant I will look at getting the centres painted or electroplated.

Pics...

First wheel finished. (centre is still painted, hosed it down to see how the raw alloy would look after the water dried)

IMAG1628.jpg

2nd Wheel pulled apart.

IMAG1642.jpg

Test polishing the centre after stripping paint. (was only a quick sand and polish, should look better when I spend more time on it)

IMAG1646.jpg

  • Like 1

I did something similar to a old 3 piece OZ Racing wheel set, only difference was they were clear coated which was peeling and really corroded.

I ended up sanding the outers to get the clear coat off, working my way to 1200 grit, with each sand removing the sand marks from the last grit.

Then buffed with a wool buff and cutting compound on a drill, final finish was done with Autosol, they came up mirrored like chrome.

You may be spending too much time on them because you are not sanding through the corrosion.

Those inners with the rough cast are best sanded smooth first to remove the rough casting, then polished.

  • Like 2
  • 1 month later...

I finally finished the first wheel today. I am really happy with how it looks but I am going to look at getting someone else to do the rest of them. Wasn't too hard just took a huge amount of time.

Still missing a few bolts that snapped when I took them out.

IMAG1715.jpg

  • Like 3
  • 2 months later...

Last update.

Finally got around to replacing a couple of bolts that snapped when I pulled apart the wheel, fitted, balanced, etc.

Really happy with how this one has turned out, but I am going to get the test polished professionally. Not worth the time or effort to do it myself. I reckon I spent 40hours on this wheel.

IMAG1856.jpg

  • Like 3

I was thinking about some sort of protection for them. I would prefer to avoid clear coat and have found references to "wheel wax" that protect raw alloy wheels. I think I will give that a try forst. The car also only does <1000kms a year, always garaged, etc so I am hoping this wheel wax stuff will suit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
    • Yeah, Duncan is helping sell me back to Android devices. I've hated the whole Android head units due to their speed issues. Even in my old Hyundai Kona (2022 model), it behind the scenes was Android, and slow and shitty to start up. Once running wasn't bad, but still a good 15 to 30 seconds.
    • My roof rails are off atm on the E39 until the rust is fixed. I did find another little bit of surface rust under the rails when I took them off. As @soviet_merlin said I'd just leave them alone unless you're planning on ensuring they're properly sealed. I was on the fence about leaving them off as the delete is still a thing in BMW E39's but I feel like the car is missing something (er, it is, der) with them off and I'm looking forward to putting them back on.
×
×
  • Create New...