Jump to content
SAU Community

Recommended Posts

Hi everyone. I searched but couldn't find anything similar to my problem.

I am trying to clean years of grim, water marks and light corrosion off my wheels. They are Enkei Winsome 3 piece wheels and have a lot of bolts that I am having trouble cleaning around. I have successfully used some metal polish to clean the dish part of the wheel and using a clay block and paint cleaner on the painted middle section of the wheels, but I am struggling to clean the water marks/corrosion around the bolts.

Has anyone got any tips?

I was thinking about removing 1 bolt at a time and cleaning that spot, replace bolt and repeat.

Is this safe?

Should I get the wheels re-balanced after I do this?

What torque for the bolts?

Am I making this more complicated than it needs to be?

Here a a few pics (I hope this works)

Corrosion/Water Marks around bolts

wheel%20bolts.jpg

Wheels before cleaning

wheel%20dirty.jpg

Wheel now.

wheel%20clean.jpg

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/459727-cleaningrestoring-3-piece-wheels/
Share on other sites

Before you take the bolts out you can try with a dremel with an extension, polishing head and some metal polish and see how you go. If no good then yes you can take a couple of bolts off at a time. You can always check the torque with a manual torque wrench when you take them off. Then use the dremel to polish it.

Its a prick of a job but well worth it.

Edited by XGTRX

Thanks Guys,

I am going to pull the wheel off the car tonight, sitting hunched over on cold concrete for 3 hours last night killed my back.

I will try with the dremel with the bolts still in first but I think it is going to be harder than removing a bolt or 2 at a time then cleaning/polishing by hand.

I will post up pics when I am done.

Trex - To get them to the stage they are now I have just used Autosol Metal Polish with a tennis ball wrapped in a microfibre cloth, the tennis ball made it easy to do the dish part of the wheel. http://www.supercheapauto.com.au/online-store/products/Autosol-Polish-Metal-350g.aspx?pid=345178#Recommendations

However, my wheel are raw alloy, no clear coat or anything. From the reading I have done online, clear coat on some wheels is really hard to cut and polish but it can be done.

For the painted middle section I have used Meguires Ultimate Compound. It is awesome stuff, cleaned up and and removed really deep scratches in the paint on my Patrol. http://www.supercheapauto.com.au/online-store/products/Meguiar-s-Ultimate-Compound-450mL.aspx?pid=214309#Recommendations

I will check out the polishing BBS RS videos tonight.

Cheers.

  • Like 1

Small update of what I got done tonight.

I tried removing 2 bolts at a time but it wasnt working very well, I let all the air out then took out 4-5 bolts at a time. Screwed around for hours before I worked out a quickish way to do it. Takes about 45nm of torque to undo the bolts so I am tightening them back up to 40nm because I figure it takes a bit extra to crack the bolt. I have decided I will get them rebalanced and checked when I am finished just to be safe.

Cleaned loose crap off with Shellite, then cleaned off the chunky corrosion with a tiny steel brush dremel attachment by hand (not in the dremel) then polished by hand the remaining scuff and marks etc with the metal polish. Cleaned up the head of the bolts with a polishing attachment in the dremel with metal polish.

It is going to take forever (took 5 hours to do about a third of the wheel) but I am really happy with the result.

Before

bolts%20before.jpg

After

bolts%20after.jpg

The wheel so far.

third%20done.jpg

  • Like 5

spent about 4 hours on mine today, arm about to fall off

has anyone dealt with deep pitting in the aluminium? i can sand it all out but some it is fairly deep and dont want to take too much material off

I have finished one of the wheels. It looks good but I am not happy with the centre.

I have decided to go all out of the next wheel. I was thinking about getting the centre electrplated (either chrome or a satin finish) but first I am going to try polishing it myself.

I completely dissasembled the wheel this time. Used paint stripper on the centre then polished up a section to see how it would look, I think I am going to be able to get it to a level I am happy with. If I cant I will look at getting the centres painted or electroplated.

Pics...

First wheel finished. (centre is still painted, hosed it down to see how the raw alloy would look after the water dried)

IMAG1628.jpg

2nd Wheel pulled apart.

IMAG1642.jpg

Test polishing the centre after stripping paint. (was only a quick sand and polish, should look better when I spend more time on it)

IMAG1646.jpg

  • Like 1

I did something similar to a old 3 piece OZ Racing wheel set, only difference was they were clear coated which was peeling and really corroded.

I ended up sanding the outers to get the clear coat off, working my way to 1200 grit, with each sand removing the sand marks from the last grit.

Then buffed with a wool buff and cutting compound on a drill, final finish was done with Autosol, they came up mirrored like chrome.

You may be spending too much time on them because you are not sanding through the corrosion.

Those inners with the rough cast are best sanded smooth first to remove the rough casting, then polished.

  • Like 2
  • 1 month later...

I finally finished the first wheel today. I am really happy with how it looks but I am going to look at getting someone else to do the rest of them. Wasn't too hard just took a huge amount of time.

Still missing a few bolts that snapped when I took them out.

IMAG1715.jpg

  • Like 3
  • 2 months later...

Last update.

Finally got around to replacing a couple of bolts that snapped when I pulled apart the wheel, fitted, balanced, etc.

Really happy with how this one has turned out, but I am going to get the test polished professionally. Not worth the time or effort to do it myself. I reckon I spent 40hours on this wheel.

IMAG1856.jpg

  • Like 3

I was thinking about some sort of protection for them. I would prefer to avoid clear coat and have found references to "wheel wax" that protect raw alloy wheels. I think I will give that a try forst. The car also only does <1000kms a year, always garaged, etc so I am hoping this wheel wax stuff will suit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...