Jump to content
SAU Community

Recommended Posts

Hi everyone. I searched but couldn't find anything similar to my problem.

I am trying to clean years of grim, water marks and light corrosion off my wheels. They are Enkei Winsome 3 piece wheels and have a lot of bolts that I am having trouble cleaning around. I have successfully used some metal polish to clean the dish part of the wheel and using a clay block and paint cleaner on the painted middle section of the wheels, but I am struggling to clean the water marks/corrosion around the bolts.

Has anyone got any tips?

I was thinking about removing 1 bolt at a time and cleaning that spot, replace bolt and repeat.

Is this safe?

Should I get the wheels re-balanced after I do this?

What torque for the bolts?

Am I making this more complicated than it needs to be?

Here a a few pics (I hope this works)

Corrosion/Water Marks around bolts

wheel%20bolts.jpg

Wheels before cleaning

wheel%20dirty.jpg

Wheel now.

wheel%20clean.jpg

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/459727-cleaningrestoring-3-piece-wheels/
Share on other sites

Before you take the bolts out you can try with a dremel with an extension, polishing head and some metal polish and see how you go. If no good then yes you can take a couple of bolts off at a time. You can always check the torque with a manual torque wrench when you take them off. Then use the dremel to polish it.

Its a prick of a job but well worth it.

Edited by XGTRX

Thanks Guys,

I am going to pull the wheel off the car tonight, sitting hunched over on cold concrete for 3 hours last night killed my back.

I will try with the dremel with the bolts still in first but I think it is going to be harder than removing a bolt or 2 at a time then cleaning/polishing by hand.

I will post up pics when I am done.

Trex - To get them to the stage they are now I have just used Autosol Metal Polish with a tennis ball wrapped in a microfibre cloth, the tennis ball made it easy to do the dish part of the wheel. http://www.supercheapauto.com.au/online-store/products/Autosol-Polish-Metal-350g.aspx?pid=345178#Recommendations

However, my wheel are raw alloy, no clear coat or anything. From the reading I have done online, clear coat on some wheels is really hard to cut and polish but it can be done.

For the painted middle section I have used Meguires Ultimate Compound. It is awesome stuff, cleaned up and and removed really deep scratches in the paint on my Patrol. http://www.supercheapauto.com.au/online-store/products/Meguiar-s-Ultimate-Compound-450mL.aspx?pid=214309#Recommendations

I will check out the polishing BBS RS videos tonight.

Cheers.

  • Like 1

Small update of what I got done tonight.

I tried removing 2 bolts at a time but it wasnt working very well, I let all the air out then took out 4-5 bolts at a time. Screwed around for hours before I worked out a quickish way to do it. Takes about 45nm of torque to undo the bolts so I am tightening them back up to 40nm because I figure it takes a bit extra to crack the bolt. I have decided I will get them rebalanced and checked when I am finished just to be safe.

Cleaned loose crap off with Shellite, then cleaned off the chunky corrosion with a tiny steel brush dremel attachment by hand (not in the dremel) then polished by hand the remaining scuff and marks etc with the metal polish. Cleaned up the head of the bolts with a polishing attachment in the dremel with metal polish.

It is going to take forever (took 5 hours to do about a third of the wheel) but I am really happy with the result.

Before

bolts%20before.jpg

After

bolts%20after.jpg

The wheel so far.

third%20done.jpg

  • Like 5

spent about 4 hours on mine today, arm about to fall off

has anyone dealt with deep pitting in the aluminium? i can sand it all out but some it is fairly deep and dont want to take too much material off

I have finished one of the wheels. It looks good but I am not happy with the centre.

I have decided to go all out of the next wheel. I was thinking about getting the centre electrplated (either chrome or a satin finish) but first I am going to try polishing it myself.

I completely dissasembled the wheel this time. Used paint stripper on the centre then polished up a section to see how it would look, I think I am going to be able to get it to a level I am happy with. If I cant I will look at getting the centres painted or electroplated.

Pics...

First wheel finished. (centre is still painted, hosed it down to see how the raw alloy would look after the water dried)

IMAG1628.jpg

2nd Wheel pulled apart.

IMAG1642.jpg

Test polishing the centre after stripping paint. (was only a quick sand and polish, should look better when I spend more time on it)

IMAG1646.jpg

  • Like 1

I did something similar to a old 3 piece OZ Racing wheel set, only difference was they were clear coated which was peeling and really corroded.

I ended up sanding the outers to get the clear coat off, working my way to 1200 grit, with each sand removing the sand marks from the last grit.

Then buffed with a wool buff and cutting compound on a drill, final finish was done with Autosol, they came up mirrored like chrome.

You may be spending too much time on them because you are not sanding through the corrosion.

Those inners with the rough cast are best sanded smooth first to remove the rough casting, then polished.

  • Like 2
  • 1 month later...

I finally finished the first wheel today. I am really happy with how it looks but I am going to look at getting someone else to do the rest of them. Wasn't too hard just took a huge amount of time.

Still missing a few bolts that snapped when I took them out.

IMAG1715.jpg

  • Like 3
  • 2 months later...

Last update.

Finally got around to replacing a couple of bolts that snapped when I pulled apart the wheel, fitted, balanced, etc.

Really happy with how this one has turned out, but I am going to get the test polished professionally. Not worth the time or effort to do it myself. I reckon I spent 40hours on this wheel.

IMAG1856.jpg

  • Like 3

I was thinking about some sort of protection for them. I would prefer to avoid clear coat and have found references to "wheel wax" that protect raw alloy wheels. I think I will give that a try forst. The car also only does <1000kms a year, always garaged, etc so I am hoping this wheel wax stuff will suit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...