Jump to content
SAU Community

Recommended Posts

I'm having some annoying problems and I'm weeding them out one by one. I got a new set of wheels for my car in 18x9 +15. They will sit on my 33 gts-t. I've got the fronts wrapped with 225/40/18 tyres and after installation I had issues with the tyres scrubbing that metal part of the body which protrudes quite a fair bit, the seam which joins the panels together(there are pics in this thread). So I did the only reasonable thing I could think of and bash the shit out of them until they were flat. I still have some scrubbing contact when throwing the weight of the car around, even lightly. My main concern was the edges cutting the tyre but now they're folded back so my main concern is why they touch on the left and not the right.

This leads me to the second concern. It APPEARS that my driver side wheel sits too far back in the wheel well. Pics attached. Opinions? I've found quite a shitload of play in the whole hub assembly too, please refer to the video. I am confident this is due to the camber arms I just installed. Everything is tight and again only evident on the RHS of the car. The RHS of the car has never been hit but prior to me owning the car the front left took a beating and it was repaired(over gutter, panel damage, some arms were replaced, it was repairable). The thing is the left feels much more solid than the right. Could adjustable castor arms incorrectly set cause any issues like this? There appears no damage to the crossmember.

Anybody able to shed some light? I really doubt I am the only skyline driver with this wheel configuration at the front. Its quite standard and not that large at all. My car sits 115mm at the lowest point on HSD coilovers.

Any feedback on anything would be good(the play, the wheel touching, wheel being too far back).

post-68383-0-71562600-1443260484_thumb.jpg

post-68383-0-45641000-1443260557_thumb.jpg

post-68383-0-14850200-1443260635_thumb.jpg

I'm uploading the video to youtube at the moment. The video shows play in assembly.

https://youtu.be/0vbFKOsTkEg

Here's a pic from my last alignment report.

post-68383-0-81668900-1443261229_thumb.jpg

Edited by SargeRX8
Link to comment
https://www.sau.com.au/forums/topic/459974-suspension-and-wheel-issue/
Share on other sites

It's not your wheels.

Reckon RHS has taken the hit as well, think you'll find the control arm bent backwards a bit. Would also explain the movement in the hub assembly, may have elongated the hole for the kingpin.

Look at replacing the lower control arm, but you may have bent or elongated the holes in the crossmember and you may need to repair/replace that. And the upright may also be damaged.

As for the alignment, add some more castor. Id add some more camber too.

It's not your wheels.

Reckon RHS has taken the hit as well, think you'll find the control arm bent backwards a bit. Would also explain the movement in the hub assembly, may have elongated the hole for the kingpin.

Look at replacing the lower control arm, but you may have bent or elongated the holes in the crossmember and you may need to repair/replace that. And the upright may also be damaged.

As for the alignment, add some more castor. Id add some more camber too.

Can I loosen bolts to check for excess play in the components and parts you specified? What do you mean by the upright? Is that the actual strut tower? It would be a mission for me to try straighten all this up. I hope tomorrow isn't raining, I get one day off a week and would really like to get under it and start doing some measurements. I installed adjustable camber arms to reduce camber, I think I'll plug the factory ones back in then, see if it eliminates play and also add the camber back and see if the wheels tuck in a little better. To add castor, do you shorten or extend the length of the castor rod?

It appears you have fitted rims to a cow..... More pictures of cow

post-68383-0-36695000-1443277362_thumb.jpg

The other problem people cause when severely kerbing/median stripping a Skyline is the front crossmember can get relocated. Slotted holes like mentioned above.

Would a damaged and crossmember give other symptoms such as vibration in the driving train? I don't think there is any vibration, but I would assume there may be some if the engine is sitting a degree out. If I loosen the bolts which hold the whole thing in place is there wiggle room for me to adjust or am I in need of a new subframe. This sounds like a huge job :(

Can I loosen bolts to check for excess play in the components and parts you specified? What do you mean by the upright? Is that the actual strut tower? It would be a mission for me to try straighten all this up. I hope tomorrow isn't raining, I get one day off a week and would really like to get under it and start doing some measurements. I installed adjustable camber arms to reduce camber, I think I'll plug the factory ones back in then, see if it eliminates play and also add the camber back and see if the wheels tuck in a little better. To add castor, do you shorten or extend the length of the castor rod?

attachicon.gif10807937_10152901512312526_1307886894_n.jpg

Would a damaged and crossmember give other symptoms such as vibration in the driving train? I don't think there is any vibration, but I would assume there may be some if the engine is sitting a degree out. If I loosen the bolts which hold the whole thing in place is there wiggle room for me to adjust or am I in need of a new subframe. This sounds like a huge job :(

I'll try to answer most of the above even though the earlier parts are not directed at my post.

First, the control arm that the 31 pig reckons you have probably bent is the lower CR, not the upper. So don't play with the camber arms you have installed hoping to work that one out. The only real way to check is to get the arm off and compare it to a known straight one, unless it is so badly rooted that you can see creases in it.

The upright is not the strut tower. The upright is the piece that runs (more or less)) vertically from the lower balljoint up to the upper bearing where the upper control arm attaches at the outer end. It's effectively the hub. Look at an exploded diagram of the Skyline suspension to get a better idea how it all goes together.

To add caster you shorten the rods. Pulls the outer end of the lower control arm forwards. Be aware that you cannot do this shit by eye. If stuff is bent, then you might end up with 2° of caster on one side and 12° on the other in order to get the wheels looking evenly located in the arches.

As to the bent/relocated front subframe causing driveline vibration....I wouldn't expect it. The uni joints in the tailshaft should be able to soak up more angle than is possible from such a tweak. But such a tweak can severely rotate the steering end of the car so that nothing looks straight. And I would not expect you to be able to loosen stuff off and try to relocate it back to where it is supposed to be. You really need to get the car into a chassis/suspension specialist who can measure the car, see how straight it is and work out what can be done, before doing it and measuring the result. You need one of those places that crash repairers use when they are having trouble straightening a car. If you were in Adelaide I could point you at one, but I don't know of any anywhere else.

Thanks for the input. My mate is bringing his 33 around hopefully later today we can do some comparisons with mine and his. I had a look at mine I removed the castor rods and the holes look nice and round. It looks straight but then again as you suggest I need something to compare it to before I give it the tick. Visually there is no paint flaking or creases on it.

These shops you are suggesting, what are they generally called? The only suspension places around me are Pedders and Jax... One of the garages down the road from me has a guy who is quite the genius when it comes to aligning and what not but I don't know if he is capable of doing what you are suggesting.

I've attached 3 images. The holes on the LCA, the length of the LCA(pretty useless) and the area where all the contact is occurring. One thing I did notice was when I disconnected the castor rod, I could very easily wiggle the whole hub left and right. This is probably to be expected though since the castor rod holds everything in place. All the contact occurs when at right full lock with the outer edge of the tyre hitting the firewall.

post-68383-0-30875000-1443324735_thumb.jpgpost-68383-0-76065400-1443324743_thumb.jpgpost-68383-0-78695200-1443324750_thumb.jpg

Edited by SargeRX8

I'll try to answer most of the above even though the earlier parts are not directed at my post.

First, the control arm that the 31 pig reckons you have probably bent is the lower CR, not the upper. So don't play with the camber arms you have installed hoping to work that one out. The only real way to check is to get the arm off and compare it to a known straight one, unless it is so badly rooted that you can see creases in it.

The upright is not the strut tower. The upright is the piece that runs (more or less)) vertically from the lower balljoint up to the upper bearing where the upper control arm attaches at the outer end. It's effectively the hub. Look at an exploded diagram of the Skyline suspension to get a better idea how it all goes together.

To add caster you shorten the rods. Pulls the outer end of the lower control arm forwards. Be aware that you cannot do this shit by eye. If stuff is bent, then you might end up with 2° of caster on one side and 12° on the other in order to get the wheels looking evenly located in the arches.

Exactly as described above.Hard to tell if theres any damage by looking at the pics. I have however been through the exact same scenario in my old 180sx and I ended up replacing both LCA's, the crossmember itself, the castor arms, a tie rod and both rod ends at the end of it all. Plus had to reweld the radiator support etc back on. T'was a moderately big hit.

Check the LCA and the crossmember with known quantities before you do anything else. Then deal with the hub/upright issue. I think that'll either be a rooted kingpin or the hub itself.

I don't think you can fix any of this by adjusting arms. :unhappy:

Comment with your alignment was referring to your alignment sheet.

I would run more camber and castor just as a rule, even on the street.

No point having adjustable arms and then hamstringing it with a shit alignment.

Edited by R31 drift pig

How hard was the crossmember to change? Control arms are easy but supporting the engine and doing all this on the ground, under the car seems tricky. Mind you I've changed my clutch on jack stands so I can probably manage this.

Yeah I wasn't too sure what to do with the alignment. I went to the shop and asked them to remove as much camber as possible to increase tyre life. The shop suggested against it but still did it for me.

What should I ask for as ideal settings for a road car?

I'll be back under the car next Sunday. 6 day working week.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
×
×
  • Create New...