Jump to content
SAU Community

Recommended Posts

Awesome. I was going to change fuel filter anyways. But you recon take fuel line off from front of the fuel rail? How much petrol should I put in to flush it out?

Run through what is in the tank first. Then add a smallish amount and run that through, then repeat. No point adding good fuel to bad in a 50/50 mix and then running half of it through leaving a 50/50 mix of old and new behind.

Keep in mind though that running a tank to the bottom can and will pick up crap from the bottom of the tank, pulling it through the pump (which might not appreciate it) and definitely putting it in the fuel filter. So don't change the filter first, and be careful about how low yo run the tank. It can of course be hard to know how much fuel is actually in the tank!

Just rereading your original post and you said you connected the battery the wrong way. I would get that ECU checked to make sure you didn't fry anything inside when you through voltage up the wrong way considering your lack of spark.

Also I would pin out the coil pack loom and make sure the coils that aren't firing are actually getting power from the ECU.

so i just did a compression test..not looking so good. i dont know exactly what this means but i cant imagine it being good that a few of the cylinders have low compression.im hoping i just didnt put the gauge in properly but im fairly sure it was in properly each time but not 100% positive.didnt have time to retest them all since it was getting too dark. but i put the new spark plugs in. didnt get a chance to test the fuel side yet..of theirs any point now :/

should mention that i haven't changed oil or the oil filter yet. could this cause lower compression ? im guessing it wouldnt make a difference.

google time !!

hrrm im hoping nothing to major. im just reading a few things on google. someone said to put a tea spoon of oil into the spark plug hole of the cylinder with low compression and redo the compression test and if its higher it means the rings are worn out and if it doesnt go higher then its the valves. least thats what im getting from what im reading. i'll redo the cylinders that had low compression tomorrow in the morning.first normal then with a bit of oil in it

yeah i noticed it was the ones next to each other. would that mean head gasket was stuffed before i got it ? or just from sitting ? i;ll be pissed if thats how the guy sold it me

lol - must have been typing at the same time.

answer is yes it could be the HG between the 2 low cylinders

ah now I see GTSboy is on the case above yours

Edited by Sinista32

somewhat freaking out lol. not giving up yet. worth getting a new head gasket? should i try the oil in the spark plug hole first or not bother and get a head gasket

Head gasket is easy fix but not so much if you don't know what your doing. It's a lot of work but not a lot of cost [emoji41]

Find a decent workshop nearby and get a quote to change it for you.

yeah i dont think i would risk doing that part myself.i've seen it done years and years ago but dont want too stuff it up. i might start googling it and watching some videos and then i'll decide if im capable of doing it on my own lol i'm hoping my cousin will come down with his g/f who's an apprentice mechanic. they're both into the nissans but not sure on their skill level. cant be worse then me though lol i'll get onto him though.looking for a head gasket now. any recommendations ?

yeah i think i;ll do the oil in the spark plug test and see if it raises.if not then i;ll look into maybe getting head gasket. if it does rise after putting oil in the hole what would i be looking to do next ? throw it out ? lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Kinda glad I never got to this ..    https://www.facebook.com/groups/1483859159195077
    • @GTSBoy This method was able to get readings of -10 to -2, so it looks like its monitoring.  Now I need to figure out why the vacuum on the line provided isn't alternating with manifold pressure.  I went with 2 lines that an RB25 tuner recommended but I'll get a longer hose and try directly off the back of the manifold.  He may have been used to OEM intake setups while I have a DBW setup that removed the MAF and IACV.  
    • I work at a car detailing and tinting shop called Quark which gets all manner of German cars in usually (mainly due to a contract with Mercedes Benz Kita Osaka, BMW Nishinomiya and others) but every once in a while something special comes in, like a fully restored 1972 HS30 Nissan Fairlady 240ZG... The shop owner had immediately started applying film to the windows as soon as it was in the shop so the interior was completely covered in towels and plastic sheets. But I could get a few photos of the engine bay which was restored like new. Such an amazing car to see in pristine condition in Japan these days.  
    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
×
×
  • Create New...