Jump to content
SAU Community

Recommended Posts

Awesome. I was going to change fuel filter anyways. But you recon take fuel line off from front of the fuel rail? How much petrol should I put in to flush it out?

Run through what is in the tank first. Then add a smallish amount and run that through, then repeat. No point adding good fuel to bad in a 50/50 mix and then running half of it through leaving a 50/50 mix of old and new behind.

Keep in mind though that running a tank to the bottom can and will pick up crap from the bottom of the tank, pulling it through the pump (which might not appreciate it) and definitely putting it in the fuel filter. So don't change the filter first, and be careful about how low yo run the tank. It can of course be hard to know how much fuel is actually in the tank!

Just rereading your original post and you said you connected the battery the wrong way. I would get that ECU checked to make sure you didn't fry anything inside when you through voltage up the wrong way considering your lack of spark.

Also I would pin out the coil pack loom and make sure the coils that aren't firing are actually getting power from the ECU.

so i just did a compression test..not looking so good. i dont know exactly what this means but i cant imagine it being good that a few of the cylinders have low compression.im hoping i just didnt put the gauge in properly but im fairly sure it was in properly each time but not 100% positive.didnt have time to retest them all since it was getting too dark. but i put the new spark plugs in. didnt get a chance to test the fuel side yet..of theirs any point now :/

should mention that i haven't changed oil or the oil filter yet. could this cause lower compression ? im guessing it wouldnt make a difference.

google time !!

hrrm im hoping nothing to major. im just reading a few things on google. someone said to put a tea spoon of oil into the spark plug hole of the cylinder with low compression and redo the compression test and if its higher it means the rings are worn out and if it doesnt go higher then its the valves. least thats what im getting from what im reading. i'll redo the cylinders that had low compression tomorrow in the morning.first normal then with a bit of oil in it

yeah i noticed it was the ones next to each other. would that mean head gasket was stuffed before i got it ? or just from sitting ? i;ll be pissed if thats how the guy sold it me

lol - must have been typing at the same time.

answer is yes it could be the HG between the 2 low cylinders

ah now I see GTSboy is on the case above yours

Edited by Sinista32

somewhat freaking out lol. not giving up yet. worth getting a new head gasket? should i try the oil in the spark plug hole first or not bother and get a head gasket

Head gasket is easy fix but not so much if you don't know what your doing. It's a lot of work but not a lot of cost [emoji41]

Find a decent workshop nearby and get a quote to change it for you.

yeah i dont think i would risk doing that part myself.i've seen it done years and years ago but dont want too stuff it up. i might start googling it and watching some videos and then i'll decide if im capable of doing it on my own lol i'm hoping my cousin will come down with his g/f who's an apprentice mechanic. they're both into the nissans but not sure on their skill level. cant be worse then me though lol i'll get onto him though.looking for a head gasket now. any recommendations ?

yeah i think i;ll do the oil in the spark plug test and see if it raises.if not then i;ll look into maybe getting head gasket. if it does rise after putting oil in the hole what would i be looking to do next ? throw it out ? lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...