Jump to content
SAU Community

Recommended Posts

Hi All,

I was driving in my 3 today in the pouring rain. I came to a corner that I have gone around no less than eleventy billion times but this time my little 3 just refused to have traction.

On approach to the right hander which is a comfortable 50kph corner and you can easily get round at 65 odd without pushing, I just lost the back end. I was doing 60 and have reviewed my dash cam footage (which looks pissy in comparison to how I had remembered it)... The front lost everything, I'm not sure if it locked up but I don't remember it pulsing or any ABS interference. The back continued to come around until the front drivers wheel went over the medium (with a big crunch) which is when I regained control and drove back over the medium and the remaining 200m to my house.

There appears to have been no interference from TCS or ABS at all. The rear just came around (oversteer) and the fronts were (likely) just spinning.

My questions are; am I expecting too much from TCS/ABS? If the (front or rear) tyres have shit wet control or if the road has had a spill of some sort, will that just stop any computers from taking control?

I am just concerned that nothing happened. The car just control (or I lost control of the car) and nothing came to my aid. If I was in the Bora, 80 separate computers will have analysed and assisted in everything from traction to window winder controls. Is there an issues with the computers in the 3? Should I be concerned?

Long winded I know, but it just freaked me out a bit.

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/461806-traction-control-abs-question/
Share on other sites

It's all good.

ABS, controls braking force only, and only activates over 16km/h.

It sees a wheel that is locked and releases the pressure to that braking circuit to let the wheel roll.

TCS, is like the yin to ABSs yang.

It sees the drive wheels turning faster than the dead wheels, and restricts engine output to slow them down.

What you're thinking about is ESC (electronic stability control)(or similar).

This take into consideration all wheel speed, steering wheel angle, g sensor readings, etc.

It then applies different braking forces to individual wheels to try and put the car where you're trying to go.

All these driving aids are either better or worse depending on tyres.

Good tyres, will help the systems.

Worse tyres, will hinder.

And there are limits to what they can do.

Push too far, and they won't be able to help.

Hope this reply hasn't bored you too much.

But, the more people know about card, the easier my job is.

  • Like 2

No, not boring at all. Its the stuff that I've pretended to know about forever.

So, as my car is supposed to have ESC and the video below shows a similar model being tested, this tells me that its potentially tyres?

If the back came around, do we blame the rear? They are older and Falkens (lots of tread) while the front are newer Hankooks.

Could be tyres, surface (different asphalt mixes), oil residue, etc.

The wet conditions certainly wouldn't be helping.

Ok, you seem very calm. Am I worrying too much about this?

Ie, just slow down in future? :)

Yep.

Drive to the conditions :thumbsup:

I've done similar in the dry in the emo.

Knew I could take the roundabout neat my house at x speed.

But, there was dirt all over the road from trucks.

Front slid a little.

Now, I slow down that little but more.

Glad to have helped :)

  • Like 1

That road should be on a closed circuit of course

Of course.

Good idea though. I did that in my Bora a few times because I was wary of the abs. If it's still raining tomorrow I'll take it somewhere local and not public.

Thanks

Remember that ABS and traction control only work on the force that's in the direction of rotation of the tyre. The sideways forces produced by cornering are at 90 degrees to the direction of rotation. So, say you enter a corner with no brakes and no accelerator, then ABS and traction control are useless, and yet its easy to imagine how you could get a sideways slip going on a wet road even though you're not braking or accelerating.

Remember that ABS and traction control only work on the force that's in the direction of rotation of the tyre. The sideways forces produced by cornering are at 90 degrees to the direction of rotation. So, say you enter a corner with no brakes and no accelerator, then ABS and traction control are useless, and yet its easy to imagine how you could get a sideways slip going on a wet road even though you're not braking or accelerating.

Yeah that makes sense. Thanks. It's been so long since I've lost it in the wet I totally flipped out (had kids in the car too.)

I'll post vid once I've gotten it off my dash cam.

Which Falkens? Zeix? If so, there's your problem.

Cars not here, my wife has it atm. But I'm 90% sure they're Ziex.

I have 4 brand new Conti's on my Bora (currently lifeless in my driveway) but they're slightly too big (225 > 215) which sucks as I'd love to swap them over.

hmmm. best to rely on driver training/skill than technology.

Without trying to compromise the lives of yourself and your family, I would try to get used to the laws of FWD. Point the front wheels in the direction you want to go, and power out. It is scary losing the rear in a FWD though.

otherwise, i think this person had the right idea:

p2.jpg

More aero, yes :P

But yeah, I'd swap those Zeix out. Never had good experience with them. My brother for some reason put 4 new ones all round on his N15 SSS. Said they're crap haha.

My BNR32 came with them, was a death trap (very used KU31s were much better).

Cars not here, my wife has it atm. But I'm 90% sure they're Ziex.

I have 4 brand new Conti's on my Bora (currently lifeless in my driveway) but they're slightly too big (225 > 215) which sucks as I'd love to swap them over.

Urggh Ziex are legendary for being crap. Change them out straight away, esp on the family car.

If the 225s are an acceptable profile, they may well be fine. Plug the details into the one of those online tyre calcs and see. IIRC +/- 4% in rolling diameter is legal (but check that I remember that correctly).

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...