Jump to content
SAU Community

Recommended Posts

Hey all

Recently my brother has bought a R31 station wagon.

Started its life as a non turbo, but has been converted on the same non turbo block to a turbo.

does it have to go through regency now?

Can i just tell motor reg its now a turbo?

Will the insurance company be ok with it being a turbo?

cheers

Link to comment
https://www.sau.com.au/forums/topic/462387-legality/
Share on other sites

I was surprised about a year ago when I found that SA Transport webpage does now list guidelines on modifications, and what is and isn't illegal. For this particular change - adding a turbocharger:

https://www.sa.gov.au/topics/transport-travel-and-motoring/motoring/vehicles-and-registration/vehicle-standards-and-modifications/aftermarket-components

Turbo-charging/supercharging petrol engine vehicles

Turbo-charging or supercharging an engine increases the power of the engine and may increase the exhaust emissions, fuel consumption and reduce the service life of the engine.

Passenger cars and passenger car derivatives (car type utilities and panel vans) manufactured prior to 1 July 1976 and fitted with petrol engines can be fitted with a turbocharger or supercharger to the original manufacturer's engine without DPTI approval.

For cars manufactured on or after 1 July 1976 the fitting of a turbocharger or supercharger requires one of the following:

  • the vehicle is fitted with a Second Manufacturer's plate to demonstrate compliance with all Australian Design Rules
  • the vehicle to pass an IM240 emissions test
  • the converted vehicle is identical to the production turbo/supercharged vehicle.

In all cases a statement of requirements is required and the vehicle must pass a roadworthiness inspection.

Certification from a professional engineer may also be required. See list of qualified engineers recognised by DPTI - MR426 Chartered Professional Engineers 409.4 KB .

I'd imagine these sorts of engineering changes would include checking over whether the brakes are adequate, any changes to the fueling system are within specifications, that adequate exhaust & emissions systems are in-place, etc.

Link to comment
https://www.sau.com.au/forums/topic/462387-legality/#findComment-7670660
Share on other sites

  • 2 weeks later...

I thought the general consensus with these cars was to keep N/A's that way, as they're then still P-plate legal, and those are in-demand. Also - the cost, engineering, legalities, and extra police attention of a converted car (and they're probably worth less than a factory turbo, or plain N/A) making it generally better to just buy the turbo car instead.

Link to comment
https://www.sau.com.au/forums/topic/462387-legality/#findComment-7677510
Share on other sites

I thought the general consensus with these cars was to keep N/A's that way, as they're then still P-plate legal, and those are in-demand. Also - the cost, engineering, legalities, and extra police attention of a converted car (and they're probably worth less than a factory turbo, or plain N/A) making it generally better to just buy the turbo car instead.

Yes, i thought so too. But people still want to do it for some reason..

I guess for them its not about the money or the legalities its about the project, and they can then complain about the whole process and unwanted attention.

Link to comment
https://www.sau.com.au/forums/topic/462387-legality/#findComment-7677574
Share on other sites

Yes, i thought so too. But people still want to do it for some reason..

I guess for them its not about the money or the legalities its about the project, and they can then complain about the whole process and unwanted attention.

Only makes sense if u have a wreck that u got for fu*k all with all the required parts to raid. Still lots of work though. I still wouldn't do but each to their own.

Link to comment
https://www.sau.com.au/forums/topic/462387-legality/#findComment-7677602
Share on other sites

Ya I understand what you guys are saying iv had my car for 6 years since on my L's and know that I can drive a turbo I was going to turbo it it more because I have spent a lot of money on it makeing it look they why I want it to look and have growin a attach meant to it and don't think I could sell it I pretty much have all the stock parts to turbo it so know it almost time to take it to the machines to get down

Link to comment
https://www.sau.com.au/forums/topic/462387-legality/#findComment-7678018
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...