Jump to content
SAU Community

Small Crack In Freshly Rebuilt Block

aaron1259

By aaron1259,
in General Maintenance

 Share

Recommended Posts

aaron1259 Explorer

aaron1259

Posted
Posted

Just got my block back from my engine builder, who said when he took the block, it was fine to use. He also said he pressure tested the block, however after closer inspection I noticed a small crack between the water jacket and the head bolt, is this block toast? Will it affect proper torquing of the head?

post-137892-14542114037703_thumb.jpg

tridentt150v Grand Master

tridentt150v

Posted
Posted

I wouldn't use it like that, its not worth the hassle - you know you will always doubt it!!! Every stutter, lurch, or engine stall will have your heart jumping. Plus the crack is only going to grow over time.

JDM33R Contributor

JDM33R

Posted
Posted (edited)

Had the same problem when i had mine built, ended up going ahead with the build dispite the crack. 50,000km on 18psi and still going strong. You wouldnt expect a 20yr old block to be perfect right??? Im not saying do it, but i havent had a problem... yet :)

Edited by JDM33R
YLD-CHLD Collaborator

YLD-CHLD

Posted
Posted

depends which headstud its around.

Was told by an engineer that it was caused by heat fatigue.DON'T quote me on that.

Had a block that had the same cracks on the exhaust side (hot) & it will cause oil to get into the water,as the crack will eventually,if not already meet the headstud then the oil that is around the headstud will get into water gallery,& slightly water into oil.

And if your wondering why there is oil around the headstud look down the headstud holes in the cylinder head & you will see the oil transfer holes for the exhaust camshaft oiling.

If using the block I would highly recommend using headstud sealer on the headstuds that have the oil holes in them,can't remember from memory what they are but pretty sure they are next to cylinder 2 & maybe 5.will check up on that.

all the best with it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RA708
      Is there a good place to learn how an engine works online?

      By RA708 · Posted

      Oh ok that makes so much sense. Thanks for clearing it up!
    • MBS206
      Is there a good place to learn how an engine works online?

      By MBS206 · Posted

      And these modern "environmentally friendly" EV vehicles also run on the same smoke! When the engine, wiring, or batteries let it escape it also stops running!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Yeah - I found the same information too.. 30% open is like 85% of flow etc. So it's probably going to be minor if not completely imperceptible. I also have a larger pod filter here, will swap that on and see if there's any difference. The hardest part is finding a place to uh, test this. It's quite noticable just how much having ducting to the otherwise completely open pod cools the intake temps down. It's better boxed, or shielded but driving for 30 seconds really makes it plummet to near ambient temperatures. I recall in the past when I was a RB land and had a nice flowing airbox -  - Then I took the lid off and put a pod there, and gained 9 psi of boost and about 60kw from the restriction I didn't know I had - with the controller at same duty cycle. However finding people using over the radiator intakes having similar KPA drops at WOT on built setups makes me think there restriction could be the exhaust or potentially the headers. Either way though, there's no real estate to play with and nothing that can realistically be done about it. The original dyno plot without the airbox, and the larger pod had a better curve. It was later I added the ducting and airbox, and a smaller pod to make it fit in there...
    • GTSBoy
      Is there a good place to learn how an engine works online?

      By GTSBoy · Posted

      That's not completely truthful now is it? Any flex fuelled factory cars also had the option to run on steam.
    • Duncan
      R33 general questions

      By Duncan · Posted

      Yeah so I guess your mechanic would know turnaround better than me....but I would have thought you had access to same day or overnight rack rebuilds there....any big city here in Australia has that service.   There are a couple of o-rings and seals involved, I guess the risk is the part is specific not general. Other option is if you can have it on stands in your garage for a while, steering rack removal is pretty simple (2 mounting brackets, 2 ball joints (separate by undoing the nut to the top of the threads, put a pry bar between the steering arm and control arm to put pressure on it then medium force on the side of the ball joint or top of the nut with a hammer to break it free) and then the trickiest bit is the splines to the steering rack (not too bad to undo, one nut then it slides out, but mark it first so you can reassemble it straight)
×
×
  • Create New...