Jump to content
SAU Community

Recommended Posts

Hey guys, I did a bit of searching around but couldn't find specific answers for this;

What would be a more suitable oil in a stockish R34 GTT - Royal Purple HPS or their new XPR oil?

It seems the XPR is a on up from the HPS, specifically for performance racing, does that mean it would not be suitable for a daily jap turbo?

This is what their website has to say; (useless)

http://www.royalpurpleconsumer.com/right-synthetic-oil/

Thanks :)

Link to comment
https://www.sau.com.au/forums/topic/462838-royal-purple-hps-or-xpr/
Share on other sites

I use hps 10w 40 In my turbo territory as its supposed to be the more daily driven oil choice with more detergents than the xpr which has higher zinc and less detergents but has a boiling point of up to 400degc from what I read from there data sheet. Both are at least a group 4 which is the more important factor here I reckon.

The ultra high performance oils (XPR, Motul 300V competion, Redline Race series) are very good in terms of dealing with high heat, high strain conditions

however this is only 1 of a 3 part equation - the are;

1. Heat tolerance - pure performance

2. Cleaners, detergents and additives - ongoing engine maintenance / protection for cold starts

3. Oil longevity (suitability for longer time/km intervals)

You have to remember racing cars differ to street cars in the fact that they;

- oil is constantly changed out every event - meaning it does not require a complex detergent/additive package to clean the bearings etc.

- constant changing also means the oil does not need to last very long time/kms wise

So the reality is the best oil for track is not the best oil for street

What you will need to settle for is an oil with a moderate heat/sheer tolerance, but also have a detergent package + resistance to acidity to last and clean over a 5000, 10,000 or 15,000km interval

If you still wanted to spend upwards of $80 my picks would be Redline (normal series) 10W40, Motul 8100 Xcess or Amsoil 10w40 (Motul and Redline are available at most Autobarns)

Good options under $50 are Penrite HPR10 (when on sale), Gulf Western Syn-X 3000, Castrol Edge 0/10w40, Valvoline SynPower 5w40

An great medium is the Gulf Western Syn X 6000 if you can find them in Autobarn, or buy direct - they are very close to your full Group V(5) ester based oils like Amsoil, Redline, Motul 300V, but at a fraction of the cost, around $50-60 i believe

Hope that helps, everyone wants the best for their ride, just need to adjust your understanding of oils to make a more informed decision

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...