Jump to content
SAU Community

Recommended Posts

So water is getting in through my boot through a small hole under the shelf in the rear close to the computers on the driver side. It's not leaking through the wing holes or the lights or the boot weather stripping. I can hose down the car or wash it and it doesn't leak but the minute it rains it leaks which makes it super hard to track down. Any idea would be greatly appreciated.

Edited by brushlessdavid
Link to comment
https://www.sau.com.au/forums/topic/463384-r32-gtr-boot-leak/
Share on other sites

Water comes in when the car is still parked in any orientation. I think it might be coming in through the plastic threaded screw holes that hold the rear windscreen molding down. Ive soaked the car with a hose on multiple occasions but it did not leak. The second it rains it leaks. Its wierd.

pull the boot weather strip off if you haven't already.

Check the rubber and where it joins. Reseal when you put it back on.

Inspect rear quarter windows

Pull the rear lights off and reseal

Remove rear wiper, check rubber and reseal

Make sure it doesn't have a leak in the hose to the squirter (as this is a gotcha for the un-initiated)

Use silastic/silicone when putting parts back in.

Edited by Sinista32

You can do the "clean it all and dust with talcum powder and see where the talcum powder is wet" trick.

I would much prefer to pressurise the whole car with smoke. If you do that please post a photo!

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...