Jump to content
SAU Community

Recommended Posts

genuine xenon kit

HID_BOX-3.jpg

XENON HID provides more than twice the amount of light of a halogen bulb, it does not have a filament. Instead the light is created by an electrical discharge between two electrodes in an air tight tiny quartz capsule filled with xenon gas, mercury and metal halide salts. This improves durability as road vibrations can cause damage to coil lighting technologies. These light sources also produce a blue-white light that is safer because it is closer to natural daylight. The color temperature is approximately 5000-13000 K compared to 2300-3000 K for halogen. The increased light output from a 35 watt XENON HID lamp is approximately 200-300% more light output than a 55 watt halogen bulb. The XENON HID system will also draw less power from your vehicles electrical system.

we will donate 5% form each sale to SAU

prices : 5000k kit RRP $879 SAU Price $709

8000k kit RRP $899 SAU Price $749

(note :H4 Hi/Lo extra $25)

fitting sizesH1, H3, H4 Lo, H4 Hi/Lo, H7,9005, 9006

if you have any queries please contact

Martin

IBS Electronics

93a Liverpool RD

Summer hill NSW 2130

phone (02)9798-7919

fax (02)9797-9471

www.ibselectronics.com.au

[email protected]

Link to comment
https://www.sau.com.au/forums/topic/46390-donation-sale-hid-kits/
Share on other sites

  • 2 weeks later...

the globes igniter and ballast are made in germany

wiring hrness and pakaging in taiwan

8000k is uv when using florescent light scale

this is light scale for gas discharge

i use the 8000k in my car

anyone is more than welcome to inspect the quality of the product and light output

just send me an email and we can meet anywhere in sydney

or you can come to my store and ill show you how it works

  • 3 weeks later...

It might sound like a dumb thing to say but I thought that to go to HID you'd need to buy new lamp assembly's that have a higher heat tolerance due to the high heat output of the Xenon discharge lamp?

Just a thought... plz correct me if I'm wrong.

Dan

xenon is actually lower heat output... these kits are manafactured to replace the bulb type in your standard headlight assembly.

Simply remove your halogen bulb and install this kit and you have converted to HID...

Its been around for some time now.

I've got a set of xenons in my r33 gts-t and they're fine. Had them for a few months now and no problems with heat/melting etc.

These hids are not the same as what I have. I don't know about this particular brand.

  • 4 weeks later...
  • 2 weeks later...
  • 4 weeks later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...