Jump to content
SAU Community

Recommended Posts

Hi all,

I'v searched both on this forum and on the internet generally and not found a definitive answer to my set of questions.

There is a lot of discussion out there about the TE37 wheels on teh AWD Sytageas but not much at all about them on a RWD Stagea.

My car is a Series 2 C34 Stagea RWD Auto. I want to fit Volk TE37 wheels but they must have the nice concaved look.

If I go for 17s or 18s, what width and offset of wheel could I use ?

Will that offset on a TE37 have that nice concave spoke look ?

Link to comment
https://www.sau.com.au/forums/topic/464680-volk-te37-on-rwd-what-size/
Share on other sites

If installed in the right offset, the TE37 spokes bend inwards going from the outside towards the middle. Thus giving the concave appearance which looks nice... see photos attached

That really depends on the thickness of the hub itself. I've seen quite a few wheels with the same width and offset but instead of concave spokes or a bigger dish, they have just had a bigger hub.. I can't tell you why they do this as it makes it a pain to get a full set or 2 full sets of identical wheels.

The reason why i said this, is the te37 could be one of the brands?

If installed in the right offset, the TE37 spokes bend inwards going from the outside towards the middle. Thus giving the concave appearance which looks nice... see photos attached

tumblr_nu3lx5dAsW1tyh5hxo1_500.jpg

staggea1.jpg?w=1000&h=666

The top car at least is a 260RS and will be AWD

Hey Bob what were your track wheels? i remember them being 3 piece and multispoke. Can you post a picture? I really liked them.

Bought them second hand off a drifter - can't remember the brand sorry...

post-49463-0-16846300-1462684672_thumb.jpg

Here ya go - 5 minutes on Google and here's what you are after - they are called TE37 Ultra Evolution Track edition (with what they call "inverted" spokes) - nothing to do with offset - they are available in a range of sizes and offsets. I suspect they will cost an arm and a leg each:

https://www.rayswheels.co.jp/products/wheel.php?lang=en&wheel=TE37ULTRA-TE

If installed in the right offset, the TE37 spokes bend inwards going from the outside towards the middle. Thus giving the concave appearance which looks nice... see photos attached

If you had bothered to click on the Link to Rays Engineering that I gave you you will see that this statement is incorrect (as is your statement that you know the model of wheel you are after). It is the particular model of TE37: "Ultra Evolution Track Edition" that gives them the inverted spoke look that you are after - nothing to do with offset - as i have already told you they are available in a full range of offsets ALL of which feature the "reinverted spokes".

17 or 18 x 8in or 9in will fit. For offset I have no idea for your car - for mine it requires different offsets front and rear.

According the the web site they only come in a 20" rim size for the ultra track edition and 19" and 20" for the Ultra

Yes quite right. Which confirms my theory that the wheels on the 260Rs cars above are Varrstoen copies (not forged but cast) which do come in 17 18 and 19 inch. Others making similar knock-offs include Koya and Rota.

If you had bothered to click on the Link to Rays Engineering that I gave you you will see that this statement is incorrect (as is your statement that you know the model of wheel you are after). It is the particular model of TE37: "Ultra Evolution Track Edition" that gives them the inverted spoke look that you are after - nothing to do with offset -

I did bother to look at the link.

Reading through it and finding that, the "track edition" is not available in rim size 18" confirmed to me that it is not the only edition that can give the inverted spoke look.

The photos below are of a car which has Volk TE37 in 18" ... not replica. These photos show the wheels to have that inverted spoke appearance which I am after.

HJA046.001.JPGHJA046.011.JPG

Edited by ceejay

I found a couple of the TE37SL variants have that look.

That is right Sir. That is exactly what I am saying too. There are several of the TE37 versions that have the inverted spoke appearance.

The spokes look more and more concave as the outer edge of the rim moves further and further towards the outside of the car, compared to the position of the hub. negative offset or the smallest positive offset.

What I want to know is, say for 17" and 18" wheels, (never mind what brand or style) what is the width and maximum offset usable, which will bring the edge of the wheel closer to the outside of the vehicle but still not cause fouling with the wheel arches.

ATV-Wheel-Offset-Explaination.jpg

Edited by ceejay

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...