Jump to content
SAU Community

Recommended Posts

  • Replies 112
  • Created
  • Last Reply

Top Posters In This Topic

Yeh i thought to myself, what if i do all this research, bloody calculations, then fork out the dough for the parts and everything, finally get it on my car and its ghey, what a waste of time... and in the end when i tried to save money originally, i think id end up spending more.

At this moment, ive made a list of turbos that would be suitable for me.

HKS 2835 56Trim .73AR, or HKS 2835R PRo (internal wastegate)

Garrett GT30 56Trim

Trust TD06SH-20G.

Ill just have to do more research and find one cheap :( hehe

You can get a new HKS GT2835ProS landed in AUS for ~3k.

The GT2835Pro version is around $100 or so cheaper.

Makes you wonder if it is worth fiddling with an external gate for this application when the ProS version has been known to make 280rwkw on 1.6bar of boost.

This is from Nengun

What turbo core and compressor cover is freebagn using in a vvvvvvl exhaust?

from memory, he's running a GT3040 core with a garrett A/R .60 compressor housing and a sierra cosworth A/R .63 exhaust housing.

Yeh i thought to myself, what if i do all this research, bloody calculations, then fork out the dough for the parts and everything, finally get it on my car and its ghey, what a waste of time... and in the end when i tried to save money originally, i think id end up spending more.

At this moment, ive made a list of turbos that would be suitable for me.

HKS 2835 56Trim .73AR, or HKS 2835R PRo (internal wastegate)

Garrett GT30 56Trim

Trust TD06SH-20G.

Ill just have to do more research and find one cheap :) hehe

here's on for ya;

http://www.japanesemotorsport.com.au/partsinstock.htm

Im thinkin of gettin a TD06-19c, mattR had one and made 286rwkw on bp98 and 313rwkw with toulene.....

 

 Decisions decisions.

Correct me if im wrong, but MattR had the TD06, then sold it and had the HKS T04-R on a manifold with twin external gates, and a Sub Zero plenum which got him up to the 313?Rwkw

Very interesting though....I have noticed (in my short turbo career:D) that no one seems to get 300 rwkw or over with an internal gate?

Anyone care to show me an example otherwise? I know you can get the 3037 Pro S which is rated the same as the 3037s, if not a little more, but has anyone actually seen good results ie 300 + rwkw on an internal gate?

Sorry for the hijack Enrico, though it may help others....including me :)

I'd say the 3037ProS will crack 300rwkw rather easily on the grounds of the 2835ProS pulling 286rwkw.

A t3/4 type back yard turbo will always have problems with boost creep due to the gate being way to small, you can only make the gate so big before you run out of room. The back yard turbo is a trial and error way of doing things, the problem is a lot of turbo shops will say 'yer it will work' yet really you are a guineepig. (Sky30 and his RB30DET)

HKS internal gates on the other hand have been designed with a large flap (45mm from memory)

Trying to find how well the 3037ProS really works is a problem, no one has published their results.

Guess your gunna have to make yourself up a guineapig suit then eh Joel :) I never had any doubt the 3037 ProS wont make it over 300rwkw...just seems too good to be true. Still requires a new manifold for the 3037ProS? If it doesnt (by memory just needed a 10mm spacer plate to clear the block?) then you are up for a new manifold...

The only added cost then is the external gate. Unless you need to spend more on the 3037 ProS to get it to hold boost, ie stiffer springs, or a top of the line boost controller...?

Catch my drift ? :D

300rwkw on the std manifold is pushing it.. :cheers:

EBC's have no issues holding boost, they work hard but do the job.

Every one needs an EBC up at that power level anyhow.

It gets too hard pushing 300rwkw.

I some times think I will settle for 270rwkw.

Slap a turbo like freebaggins on it and be happy with the response and stocker look.

I may have to talk to sky30 to see how happy he really is with the larger laggier turbo over his initial 240rwkw setup.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...