Jump to content
SAU Community

Recommended Posts

Pedestrian Safety Help

Hello!

Had to make an account because i have no idea how to tackle this situation i am in. I own a 370gt Coupe, 2009, and the other night i was driving around as i watched 2 kangaroos hop out infront of me and off to the side, but little did i know a 3rd kangaroo would jump into the side of my car!

This made a loud bang and the hood popped up (Pedestrian Safety System). No exterior damage, just the dirt off his body at the end of the drivers side door just before the wheel.

So im just wondering how to get the hood to retract back to its original position and to get rid of the warning light, unsure if i have to go to a Nissan dealer or if there is any other way.

Any help is appreciated.

Cheers,

Scott

Link to comment
https://www.sau.com.au/forums/topic/467534-pedestrian-safety-help/
Share on other sites

Unfortunately, those things are like airbags. It's a one-time deal. You need to replace them with new ones.

I'm contemplating unplugging mine and replacing them with little adapters that keep the BCM happy. May not be the legally appropriate thing to do but I don't have a heart to care enough.

You could always ask a dealer for a quote. As for the parts, if you can score them from a wrecked vehicle, you could be in luck but I wouldn't know the probability of that. In which case, grab the part number pertaining to your series and search for it on Google, particularly from Amayama, who seem to be a pretty good source for Jap parts. Failing that, your dealership's spare parts division would be the only other way.

Having recently resolved a problem with having to replace my rear seat, I've found the price from Amayama and the price from Steve Jarvin's spare parts division works out to be pretty much even. I'd rather pay a small percentage more with the local guys, if nothing else, to kick their arse if they got it wrong despite my best description and triple-checking with them.

Thanks for the reply Max! Amayama seems like a good site, thankyou for that!

I just took the car down to a private panel beater i know. He said he can attempt to get rid of the whole system and try to get the bonnet down. I would rather get rid of it rather then have it all setup again, because it is too much of an inconvenience and how often does one hit a pedestrian? Is this a Japanese safety law?

If all that fails, i believe i will head to the dealer. Fingers crossed the bonnet is flush and the system is gone!

Getting the struts out isn't the problem. It'll be the annoying error light in your dash that will piss you off because it's nagging at you that you have them both disconnected. That's where you need a couple of plugs which have little electronic modules within (which I have yet to see for myself and inspect) to fool the system into thinking they're plugged in and ready to go.

I believe this is becoming a standard feature worldwide. My European buddies tell me a lot more modern vehicles are made curvier and with all these fancy features in the interest of pedestrian safety, reducing the risk of them flying through your windscreen, etc. I can't say I agree with the practice but there you go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...