Jump to content
SAU Community

Nismo Engine Mount Height Increase?

No Crust Racing

By No Crust Racing,
in General Maintenance

 Share

Recommended Posts

89CAL Grand Master

89CAL

Posted
Posted (edited)

Is a height increase likely to be an issue? I never noticed much of a difference with mine. I think I even held them up back to back with stock and couldnt really see a difference. If they are harder there may be a little less 'squish' with the weight of the engine but nothing crazy I would imagine.

The top of my engine is quite low because of the front facing plenum but if it helps:

14268147293_78f04134c4_h.jpg

 

 

20131205_194100_zps213145be.jpg

Edited by 89CAL
V28VX37 Veteran

V28VX37

Posted
Posted
3 hours ago, ActionDan said:

Nismo Engine Mount Height Increase?

What sort of height increase are we talking in an R34 GT-R and what other options are there that don't increase the height? 

FWIW my R34 GT-T Nismo mounts didn't seem to make any difference to where the engine is sitting.

I would have thought there might be a couple of mm difference in just the OEM mounts being squished & worn out over 15+ years...?

No Crust Racing Grand Master

No Crust Racing

Posted
  • Author
Posted

Issue would stem from what potentially happens with intake pipes as I replaced the standard suction pipes with kts suction pipes and have a jsai pod enclosure which barely clears the z tune style bonnet.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...