Jump to content
SAU Community

Recommended Posts

Lads and ladettes,

couple of spare sets of wheels up for sale....

17x9+12 volk gramlight 57D, satin black colour (set): $1200.....new in box

IMG_1330.JPG

IMG_1371.JPG

IMG_1335.JPG

17x9+12 volk gramlight 57D, luminous orange colour (set) $1500 with 235/40 and 255/40 Nitto NT01 semi slicks fitted (old but only a couple track days of use). Few scratches from use and tyre fitting

IMG_0843.JPG

2.JPG

3.JPG

17x9.5+15, 18x10+25 advan RS, silver colour (set): $2000
17s fitted with 235/40/17 Federal 595 tyres (old but good tread),  18s fitted with 245/40/18 Federal RSR tyres (few years old but never driven on)

IMG_20170110_173559.jpg

IMG_20170110_173611.jpg

 

DSC00772.JPG

IMG_0831.JPG

Edited by boost_bus180

Mazworx SR20VE P11 inlet manifold: $600 brand new never fitted comes with fuel rail still in packet and other vac fittings. Can include a smaller flange from plazmaman for an extra $30

IMG_20170110_152804.jpg

IMG_20170110_152814.jpgIMG_20170110_152834.jpgIMG_20170110_152307.jpgIMG_20170110_152529.jpg

 

MAZWORX SR20 -16 water outlet fittings (hot and cold side): $40 (new) IMG_20170110_153228.jpg

 

APEXI DECS tacho: $300 (new) was fitted and wired up but swapped to a digital dash before it ever got used. Super cool old school discontinued Japness that should have been more popular than it was. cost me nearly $600

DSC01567.JPGDSC01570.JPGDSC01580.JPG

Bosch 044 fuel pump (genuine, of course!) bought by mistake. still in original packaging: $140

IMG_20170110_172854.jpgIMG_20170110_172903.jpg

17x9+37 volk racing emu, black (pair): $200.... no tyres fitted. plenty of marks on them. good skid wheels. 4/5 multi-stud.

IMG_20170110_171242.jpg

17x8+32 volk racing emu, black (single): $100... fitted with a 235/45 potenza tyre. kept as a spare but never needed it. 4/5 stud

IMG_20170110_173028.jpg

TAARKS S13/180sx poly-carbonate door windows: $100... pre-moulded and drilled ready to install for a factory fit. weigh half as much as standard. never fitted.

IMG_20170110_170818.jpg

APEXI gauge controller: $40 (new)

IMG_0377.JPGIMG_0374.JPGIMG_0373.JPG

 

Turbosmart manual boost controller/bleed valve: $15

IMG_20170110_172353.jpg

stock R33 RB25 airbox with snorkel: $100 (no extra charge for the hectic K&N sticker)

IMG_20170111_103121.jpg

IMG_20170111_103136.jpg

 

POTENZA 'damper for wagon' suspension with wild dog springs to suit C34 series 1 stagea: $200..... unknown kms - was in the car when I bought it. No leaks or knocks. quite stiff. removed cos I wanted to try some nismo ones but they feel very similar.

IMG_20170111_102841.jpg1.jpg

 

 

5 x RB25 coil packs from a series 1 Stagea: $40.... were working fine but kept these as spares after upgrade

IMG_20170111_130602.jpgIMG_20170111_130612.jpg

RB25 auto radiator from series 1 Stagea: $20.... no leaks or damage. worked fine but upgraded. Good to have as a spare for our bullshit-hot summers

IMG_20170111_131514.jpgIMG_20170111_131529.jpg

RB25 radiator fan: $20.... no damage

IMG_20170111_131639.jpgIMG_20170111_131647.jpg

HKS super sucky sucky long time air filter with AFM adapter: $20

IMG_20170111_130411.jpgIMG_20170111_130432.jpg

BLITZ cannon exhaust stainless silencer: $20.... knocks a few louds off your exhaust note so you can sneak home without pissing off the neighbors

IMG_20170111_132203.jpgIMG_20170111_132243.jpg

Space saver with new tyre: $10..... sweet paint job and even better offset. will make your RB20DE auto single-peg like a champ.... and also get you out of trouble if you get a flat.

IMG_20170111_132344.jpgIMG_20170111_132358.jpg

RB25 coil pack valley cover: $20 in excellent original condition

IMG_20170112_120143.jpgIMG_20170112_120202.jpg

 

SR20 S13 carbon fiber coil pack valley cover: $50

IMG_20170110_151434.jpg

Edited by boost_bus180

This Volks, the 9" wide ones, can you show me those in more detail. I wanna see if the colour matchs mine as it might save me painting this purple set I bought to get the 9s

Is it the same colour as this? 

A charcoal type black rather than a really dark black? 

 

10699709_10153288426534838_5124629831311483969_o.jpg

Hi mate, can u get back to me on 0432 446 550 I want to put cash in your acc for a bunch of parts so I don't miss them can wait till u get back to send them or I'll pick them up but really want to put the cash in to secure them, again please text me on the phone number provided,

cheers,

Sean....

  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 1 month later...

Parts still available include the following:

17x9+12 volk gramlight 57D, luminous orange colour (set): $1200
17x9.5+15, 18x10+25 advan RSII, silver colour (set): $2000 
17x8+32 volk emu, black colour (single): $100
space saver 5 stud: $10
180SX tinted rear hatch glass: $20
NISSAN S15 engine mounts SR20: $100 (new)
BLITZ exhaust silencer: $20
Turbosmart manual boost controller: $15
Front seats to suit Series 1 C34 Stagea: $20/pair
POTENZA shocks with Sheep Dog springs Series 1 C34 Stagea suspension: $200 

RB25 air box: $40
RB25 air box with snorkel: $100
RB25 auto radiator from Series 1 C34 Stagea: $20
RB25 radiator fan: $20
RB25 coil packs (5) to suit Series 1 C34 Stagea: $40

Edited by boost_bus180

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...