Jump to content
SAU Community

Recommended Posts

R34 steering rack

Anybody know if there is a difference in an automatic steering rack and a manual one on the r34??

i have a plug on my alternator loom for the steering rack but I have no sensor on the rack for it to plug into, thinking i may have an auto steering rack?? My car is a factory manual

 

first photo is my rack, and second photo is one of the net

IMG_4474.JPG

IMG_4472.JPG

Link to comment
https://www.sau.com.au/forums/topic/469026-r34-steering-rack/
Share on other sites

The plug should go on the hard line before it enters the rack, not on the rack itself, trace from the high pressure line and you should be able to find it, I think it's near the oil filter area

My r34 steering rack definitely didn't have any sensor or valve and it's a manual

1 minute ago, chiksluvit said:

The plug should go on the hard line before it enters the rack, not on the rack itself, trace from the high pressure line and you should be able to find it, I think it's near the oil filter area

My r34 steering rack definitely didn't have any sensor or valve and it's a manual

Okay well I've looked at a whole heap of photos, manuals, turbo and na, and some have the plug and some don't, so I'm assuming it's been changed over the years or something, thank heaps for the reply 

I Did tell you about this in your other thread.

Does your steering feel heavy when driving around parking lots? The plug on the rack is for the power assist solenoid. It controls how much assistance the power steering gives, Lots at low speed and not much/none at higher speeds

The switch on the pressure line is for idle. When you steer it bumps up the idle, especially important when the air con and alternator are working

3 hours ago, chiksluvit said:

Sorry my bad
Had a look at my car last night and there IS a brown plug on the rack
IMG_1486940405.672147.jpg

 


Can't really see the plug but you can see the harness coming out of the rack

There is another plug on the high pressure line tho, might be that?

 

Yeah see mine doesn't have that harness Coming of the rack, it's for the idle control when steering, but I don't know why some racks have them and some don't 

2 hours ago, 89CAL said:

I Did tell you about this in your other thread.

Does your steering feel heavy when driving around parking lots? The plug on the rack is for the power assist solenoid. It controls how much assistance the power steering gives, Lots at low speed and not much/none at higher speeds

The switch on the pressure line is for idle. When you steer it bumps up the idle, especially important when the air con and alternator are working

Yes and that helped me mate thanks!

 

The plug is for the idle control but I've looked at different photos of different racks and some have the plug and some don't, my rack hasn't got it but my loom does because I changed it

Interestingly there is a mechanical valve that comes off the PS pump on the banjo that controls the idle. I've taken that off and blocked it when I changed my pressure line, just raised the idle a little

My guess is the one on the rack is could be for variable steering assist? Could be a HICAS model vs non HICAS model difference?

These r34s are a bit more complex than r33 I found...

1 minute ago, chiksluvit said:

Interestingly there is a mechanical valve that comes off the PS pump on the banjo that controls the idle. I've taken that off and blocked it when I changed my pressure line, just raised the idle a little

My guess is the one on the rack is could be for variable steering assist? Could be a HICAS model vs non HICAS model difference?

These r34s are a bit more complex than r33 I found...

I thought it could of been for hicas models too but I'm pretty sure hicas only affects the rear steering racks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...